{"title":"Vehicle Detection","description":"\u003cp\u003eVehicle detection equipment tells a gate operator when a car is in the lane, so the gate opens for exit traffic and holds open while a vehicle is in the path. Protec Controls carries loop detectors from Reno A\u0026amp;E, Diablo Controls, EMX and EDI, preformed loops from Reno A\u0026amp;E and BD Loops, EMX buried probes, AES e-Loop wireless kits, and loop wire and sealant. Installers and property managers use it on free-exit and safety lanes.\u003c\/p\u003e","products":[{"product_id":"sarasota-625x-lv-loop-detector","title":"Sarasota 625X Loop Detector  12-24vac\/dc","description":"\u003ch4\u003eDescription\u003cbr\u003e\n\u003c\/h4\u003e\n\u003cp class=\"sm\"\u003eThe 625X detector is a single-channel inductive loop vehicle detector that provides vehicle presence information required by gate operators, ticket spitters, card readers, etc. Although compact and lightweight, the 625X is designed to operate in the most demanding high volume access control installations in all environmental conditions. The 625X detector does not sacrifice features for the evolutionary reduction of size.\u003c\/p\u003e\n\u003cp\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003cp class=\"sm\"\u003eTwo outputs are available: one to provide the presence of a vehicle over the loop, the second is switch selectable to provide pulse on entry of the loop, pulse on exiting the loop, a second presence output or a loop fault output. Easy-to- use front panel slide switches provide positive identification of frequency and sensitivity settings.\u003c\/p\u003e\n\u003ch4\u003eFeatures\u003c\/h4\u003e\n\u003cul\u003e\n\u003cli\u003eFailsafe or failsecure outputs\u003c\/li\u003e\n\u003cli\u003eFour selectable sensitivities\u003c\/li\u003e\n\u003cli\u003ePulse on entry and exit\u003c\/li\u003e\n\u003cli\u003eSecond presence output\u003c\/li\u003e\n\u003cli\u003eLoop fault output\u003c\/li\u003e\n\u003cli\u003eGalvanic separation of loop and detector electronics\u003c\/li\u003e\n\u003cli\u003eAutomatic tuning\u003c\/li\u003e\n\u003cli\u003eConstant readjustment of frequency to avoid environmental impacts\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4\u003eSpecifications\u003c\/h4\u003e\n\u003cul\u003e\n\u003cli\u003eDimensions: 3\" H x 1.5\" W x 2.8\" L (76 x 38 x 71 mm)\u003c\/li\u003e\n\u003cli\u003eSupply Power: 10-30 V AC\/DC\u003c\/li\u003e\n\u003cli\u003eFrequency Range: 30 to 130 kHz\u003c\/li\u003e\n\u003cli\u003eInductance: 20 to 700 μ\u003cspan\u003eH\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cspan\u003eTemperature range: \u003c\/span\u003e\u003cspan\u003e-35\u003c\/span\u003e°\u003cspan\u003eF to 158\u003c\/span\u003e°\u003cspan\u003eF   (-37\u003c\/span\u003e°C to 70°C)\u003c\/li\u003e\n\u003cli\u003eWeight: 5.8 oz (165 grams)\u003c\/li\u003e\n\u003cli\u003eMaterial: ABS plastic\u003c\/li\u003e\n\u003cli\u003eConnection: 11 pin male\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch4\u003eTechnical Information\u003c\/h4\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cform action=\"https:\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/loop_install_guide.pdf?1645050349120890010\" method=\"Get\"\u003e\u003cbutton class=\"btn\" type=\"submit\"\u003eLoop Install Guide\u003cspan\u003e \u003c\/span\u003e\u003c\/button\u003e\u003c\/form\u003e\u003cform action=\"https:\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/loop_installation_guidelines.pdf?1645050349120890010%22\" method=\"Get\"\u003e\u003cbutton class=\"btn\" type=\"submit\"\u003eLoop Installation Guidelines\u003cspan\u003e \u003c\/span\u003e\u003c\/button\u003e\u003c\/form\u003e\u003cform action=\"https:\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/LoopSizes.pdf?3158443000636428019\" method=\"Get\"\u003e\u003cbutton class=\"btn\" type=\"submit\"\u003eSize Chart\u003cspan\u003e \u003c\/span\u003e\u003c\/button\u003e\u003c\/form\u003e\n\u003cdiv id=\"awebChromeHelper\"\u003e\u003c\/div\u003e","brand":"Sarasota","offers":[{"title":"Default Title","offer_id":21951456323,"sku":"PT 625X-LV","price":315.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/625X_124e8c9a-6bea-405e-b2fa-cf2b3b680451.png?v=1672351657"},{"product_id":"elite-a-79-loop-detector","title":"Elite A-79 Loop Detector","description":"\u003cp\u003eThe Elite A-79 is a vehicle loop detector that runs on 115 VAC. It connects to a buried inductive loop and signals the gate operator when a vehicle is over the loop.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003ePower: 115 VAC. Confirm the operator supplies 115 VAC to the detector.\u003c\/li\u003e\n\u003cli\u003eCheck the connector and mounting on your existing detector before ordering.\u003c\/li\u003e\n\u003cli\u003eLoops are sold separately.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Elite","offers":[{"title":"Default Title","offer_id":21951471107,"sku":"A-79","price":210.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/Elite_20A-79.jpeg?v=1465925479"},{"product_id":"northstar-np2-loop-detector","title":"Northstar NP2 Loop Detector 110vac","description":"\u003cp\u003eSingle Channel-Dual Relay Inductive Loop Vehicle Detector\u003cbr\u003e\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e","brand":"Northstar Controls, LLC","offers":[{"title":"Default Title","offer_id":21951485443,"sku":"NP2110","price":109.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/NP2.webp?v=1698342448"},{"product_id":"doorking-9410-single-channel-loop-detector","title":"Doorking 9410-010 Single Channel Loop Detector","description":"\u003cp\u003eThe DoorKing 9410-010 is a single-channel plug-in vehicle loop detector for DoorKing gate operators. It plugs into the loop detector port on the operator control board, so only the loop lead-in needs wiring.\u003c\/p\u003e\u003cp\u003eSelf-tuning circuitry tracks loop drift and weather changes. Four frequency and four sensitivity settings. Sensitivity boost raises sensitivity once a vehicle is detected so high-bed vehicles are not lost. Fast-Trak, a loop fault monitor with a flashing LED, a frequency readout on the LED at power-up, and a reset button.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eDoorKing lists the 9409, 9410 and 9411 plug-in detectors for its legacy operators. Check the operator manual for the correct detector.\u003c\/li\u003e\n\u003cli\u003eLoop not included. DoorKing preformed loops are 4 x 8 ft with 50 ft lead-in.\u003c\/li\u003e\n\u003cli\u003eMinimum loop size is 18 x 48 in. Detection height is about 1\/2 to 2\/3 of the short side.\u003c\/li\u003e\n\u003cli\u003eTwist lead-in wires 6 turns per foot. Set nearby loops to different frequencies.\u003c\/li\u003e\n\u003cli\u003eLow-power version for solar operators: 9416-010.\u003c\/li\u003e\n\u003cli\u003eFamily: 9410-010 single channel, 9409-010 dual channel, 9411-010 single channel with aux relay.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Doorking","offers":[{"title":"Default Title","offer_id":21951539267,"sku":"9410-010","price":165.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/IMG_2506.jpg?v=1700152420"},{"product_id":"doorking-9409-dual-channel-loop-detector","title":"Doorking 9409-010 Dual Channel Loop Detector","description":"\u003cp\u003eThe DoorKing 9409-010 is a dual-channel plug-in vehicle loop detector for DoorKing gate operators. It plugs into the loop detector port on the operator control board. Loop 1 feeds the control board directly and loop 2 switches a dry contact relay.\u003c\/p\u003e\u003cp\u003eSelf-tuning circuitry tracks loop drift and weather changes. Four frequency and four sensitivity settings. Sensitivity boost raises sensitivity once a vehicle is detected so high-bed vehicles are not lost. Fast-Trak, a loop fault monitor with a flashing LED, a frequency readout on the LED at power-up, and a reset button.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eDoorKing lists the 9409, 9410 and 9411 plug-in detectors for its legacy operators. Check the operator manual for the correct detector.\u003c\/li\u003e\n\u003cli\u003eLoop not included. DoorKing preformed loops are 4 x 8 ft with 50 ft lead-in.\u003c\/li\u003e\n\u003cli\u003eMinimum loop size is 18 x 48 in. Detection height is about 1\/2 to 2\/3 of the short side.\u003c\/li\u003e\n\u003cli\u003eTwist lead-in wires 6 turns per foot. Set nearby loops to different frequencies.\u003c\/li\u003e\n\u003cli\u003eLow-power version for solar operators: 9415-010.\u003c\/li\u003e\n\u003cli\u003eFamily: 9410-010 single channel, 9409-010 dual channel, 9411-010 single channel with aux relay.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Doorking","offers":[{"title":"Default Title","offer_id":21951540931,"sku":"9409-010","price":235.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/9409-010.jpg?v=1700228350"},{"product_id":"loop-detector-harness","title":"EMX HAR-11 Loop Detector Harness","description":"\u003cp\u003eThe EMX HAR-11 is an 11-pin wire harness for loop detectors with a round 11-pin plug (86CP11 \/ JEDEC B11-88 style). It plugs onto the detector and gives you 3 ft of color-coded leads in place of a DIN socket or terminal block.\u003c\/p\u003e\u003cp\u003eThe harness has 11 non-jacketed #20 AWG wires, one per pin, covering power, loop and relay NO, NC and C contacts.\u003c\/p\u003e\u003ch4\u003eWhat's Included\u003c\/h4\u003e\u003cul\u003e\u003cli\u003eHAR-11 11-pin harness, 3 ft leads\u003c\/li\u003e\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eFits EMX D-TEK, MVP D-TEK, LP D-TEK, ULT-MVP and ULT-MVP-2 detectors.\u003c\/li\u003e\n\u003cli\u003eDoes not fit the ULT-PLG (10-pin plug-in) or the ULT-DIN (screw terminals).\u003c\/li\u003e\n\u003cli\u003eUse the wiring chart in your detector manual to match wire colors to pins.\u003c\/li\u003e\n\u003cli\u003eFor a DIN rail mount, use the LD-11 11-pin socket instead.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EMX","offers":[{"title":"Default Title","offer_id":21951541059,"sku":"HAR-11","price":19.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/HAR-11.webp?v=1697831511"},{"product_id":"loop-detector-din-block-socket","title":"Loop Detector DIN Block\/Socket","description":"\u003cp\u003eThis is a DIN rail mount socket for loop detectors with a round 11-pin plug. Plug the detector in and land the field wiring on the socket terminals.\u003c\/p\u003e\u003cp\u003eUse it to mount a plug-in loop detector in a control panel or enclosure instead of a gate operator harness. The detector shown in the photo is not included.\u003c\/p\u003e\u003ch4\u003eFeatures\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eAccepts round 11-pin plug-in loop detectors\u003c\/li\u003e\n\u003cli\u003eDIN rail mount\u003c\/li\u003e\n\u003cli\u003eWiring lands on the socket, so the detector can be swapped\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eCheck your loop detector has a round 11-pin plug.\u003c\/li\u003e\n\u003cli\u003eLoop detector not included.\u003c\/li\u003e\n\u003cli\u003eDIN rail not listed as included.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Protec Controls","offers":[{"title":"Default Title","offer_id":21951541379,"sku":"DIN Block 11","price":16.2,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/din_socket.png?v=1470334926"},{"product_id":"emx-carsense-101-probe-detector-requires-in-ground-probe","title":"EMX Carsense CS-101 Probe Detector 12-24v ac\/dc","description":"\u003cp\u003eEMX CarSense 101 (CS-101) vehicle motion detector. It is the control module for the CarSense in-ground probe. It plugs into a standard 11-pin (86CP11) socket and runs on 9 to 41 VDC or 6 to 29 VAC. Use it as a free exit detector for gates, overhead doors and parking barriers, or to trigger warning lights, alarms or cameras when a vehicle moves along a drive.\u003c\/p\u003e\u003cp\u003eThe CS-101 detects moving vehicles only. It is not a presence detector. Detection range is roughly a 15 ft diameter around the probe and changes with vehicle size and speed. Output is a DPDT relay rated 1 A at 24 VDC and 120 VAC. Front panel controls set sensitivity (high\/low plus a continuous adjustment) and an off delay of 1 to 5 seconds. A green LED shows power and a red LED shows detect. Standby draw is 2.5 mA max and detect draw is 50 mA max, so EMX lists it for solar power applications. Warranty is 2 years from EMX.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eThe probe is sold separately. Order the CarSense in-ground probe in the lead length you need (50 ft, 100 ft, 150 ft or 200 ft).\u003c\/li\u003e\n\u003cli\u003eNeeds an 11-pin (86CP11) detector socket on the operator or control board, or a separate 11-pin socket base.\u003c\/li\u003e\n\u003cli\u003ePower: 9 to 41 VDC or 6 to 29 VAC.\u003c\/li\u003e\n\u003cli\u003eMotion detection only. For vehicle presence on a stopped vehicle, use a loop detector or the EMX LRS.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EMX","offers":[{"title":"Default Title","offer_id":21951602115,"sku":"CS-101","price":122.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/CS101_945072c1-52b7-4a92-9c73-84f9b198c21e.jpg?v=1697744543"},{"product_id":"emx-carsense-in-ground-buried-vehicle-probe-requires-detector","title":"EMX Carsense In-Ground Buried Vehicle Probe (Requires Detector) 50'","description":"\u003cp\u003eEMX CarSense in-ground vehicle probe with a 50 ft lead (SKU Probe-50). This is the sensing probe for the EMX CarSense 101 (CS-101) vehicle motion detector. The probe senses a moving ferrous vehicle by the change it causes in the earth's magnetic field. It has no loop to saw cut into the pavement.\u003c\/p\u003e\u003cp\u003eThe probe is a sealed PVC tube, 17 in long and 1 in diameter, on a shielded direct burial lead-in cable. This listing has the 50 ft lead. EMX rates the probe for -40°F to 170°F. The CS-101 detects moving vehicles only. It is not a presence detector.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eRequires the EMX CarSense CS-101 detector, sold separately.\u003c\/li\u003e\n\u003cli\u003ePick the lead length that reaches from the probe location to the CS-101 without a splice. Lead lengths offered here: 50 ft, 100 ft, 150 ft and 200 ft.\u003c\/li\u003e\n\u003cli\u003eEMX calls for burying the probe at least 6 in deep, parallel to the driveway, where it cannot move.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EMX","offers":[{"title":"Default Title","offer_id":21951602691,"sku":"Probe-50","price":92.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/Probe-1001_8a8904c4-426f-44b3-81cf-319bd33b5f0d.jpg?v=1697745604"},{"product_id":"bea-10matrixiis110-single-channel-loop-detector-with-din-block","title":"BEA 10MATRIXIIS110 Single Channel Loop Detector with Din Block","description":"\u003cp\u003eThe BEA 10MATRIXIIS110 is a single channel digital inductive loop detector (MATRIX2-S) for vehicle detection at gates, barrier arms and industrial doors. This model runs on 110 to 120 VAC and uses a standard 11-pin round connector (86CP11).\u003c\/p\u003e\u003cp\u003eSensitivity (0.005% to 0.5%) and presence time (1 minute to infinite) are set by potentiometer. Two relay outputs with changeover contacts (5 A at 230 VAC resistive) can run in presence or pulse mode, with pulse on entry or exit. Automatic sensitivity boost keeps high-bed vehicles detected. Four frequency settings help prevent crosstalk between adjacent loops. A DIP switch sets fail-safe or fail-secure relay operation. Loop inductance range is 20 to 1000 µH and reaction time is 25 ms.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003ePower: 110 to 120 VAC. For 12 to 24 VAC\/VDC power, order the 10MATRIXIIS1224.\u003c\/li\u003e\n\u003cli\u003eNeeds a field-installed inductive loop and an 11-pin round socket. This listing is titled with a DIN block.\u003c\/li\u003e\n\u003cli\u003eFor two independent loops, see the dual channel 10MATRIXD110 (110 to 120 VAC) or 10MATRIXD1224 (12 to 24 VAC\/VDC).\u003c\/li\u003e\n\u003cli\u003eOperating temperature is -22 °F to 158 °F. Housing is IP40.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"BEA","offers":[{"title":"Default Title","offer_id":21951604227,"sku":"10MATRIXIIS110","price":136.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/IMG_2623.jpg?v=1701799987"},{"product_id":"bea-10matrixd110-dual-channel-loop-detector","title":"BEA 10MATRIXD110 Dual Channel Loop Detector","description":"\u003cp\u003eThe BEA 10MATRIXD110 is a dual channel digital inductive loop detector for vehicle detection at gates, barrier arms and industrial doors. It monitors two independent loops, each with its own relay output. This model runs on 110 to 120 VAC and uses a standard 11-pin round connector (86CP11).\u003c\/p\u003e\u003cp\u003eEach loop output can be set for presence or pulse and has common, normally open and normally closed contacts (5 A at 230 VAC resistive). Sensitivity (0.005% to 0.5%) and presence time (1 minute to infinite) are set by potentiometer. Automatic sensitivity boost keeps high-bed vehicles detected. Each loop has two frequency settings. Loop inductance range is 20 to 1000 µH and reaction time is 50 ms per channel.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003ePower: 110 to 120 VAC. For 12 to 24 VAC\/VDC power, order the 10MATRIXD1224.\u003c\/li\u003e\n\u003cli\u003eNeeds two field-installed inductive loops and an 11-pin round socket.\u003c\/li\u003e\n\u003cli\u003eFor a single loop, see the 10MATRIXIIS110 (110 to 120 VAC) or 10MATRIXIIS1224 (12 to 24 VAC\/VDC).\u003c\/li\u003e\n\u003cli\u003eOperating temperature is -22 °F to 158 °F.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"BEA","offers":[{"title":"Default Title","offer_id":21951604867,"sku":"10MATRIXD110","price":160.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/beamatrix.jpeg?v=1465925608"},{"product_id":"proseal-6006-can","title":"ProSeal 6006 Loop Sealant 1 Gallon Can","description":"\u003cp\u003eRAI Products ProSeal 6006 is a two-component, pourable loop sealant for vehicle detector loop saw cuts in asphalt and concrete. Sold per 1 gallon can with 2 tubes of catalyst.\u003c\/p\u003e\u003cp\u003eIt encapsulates and insulates the loop wire and keeps out moisture and road debris. It is flexible, self-leveling and does not shrink. No pump or caulking gun is needed. Mix 1 to 2 tubes of catalyst into the can with a drill and paint mixer for about 30 seconds, until the color is even with no red streaks. Pour from the can and smooth into the slot with a V-shaped squeegee. The sealant is dark brown and the catalyst is dark red.\u003c\/p\u003e\u003ch4\u003eWhat's Included\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e1 gallon can of ProSeal 6006\u003c\/li\u003e\n\u003cli\u003e2 tubes of catalyst (liquid hardener)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eExtra catalyst tubes are sold separately as Liquid Hardener for ProSeal 6006.\u003c\/li\u003e\n\u003cli\u003eClosest replacement for the discontinued Bondo P606 loop sealant.\u003c\/li\u003e\n\u003cli\u003eWorks in both asphalt and concrete saw cuts.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"RAI Products","offers":[{"title":"Default Title","offer_id":21951608323,"sku":"ProSeal 6006","price":68.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/6006can.jpeg?v=1536876866"},{"product_id":"bondo-p606-loop-sealant-gallon-can-w-2-tubes-liquid-hardener","title":"Bondo P606 Loop Sealant - Gallon Can w\/ 2 tubes liquid hardener ***Discontinued***","description":"\u003cp\u003eDiscontinued by Bondo \/ 3M. The Durant STAT-A-FLEX is the updated version. Bondo P-606 (part 00606) is a two-part flexible polyester loop sealant in a 1 gallon can, supplied with MEKP liquid hardener. The base is gray and the hardener is red.\u003c\/p\u003e\u003cp\u003eAt 77°F, gel time is 9 to 15 minutes and initial cure is 35 to 45 minutes. One gallon of mixed sealer fills about 51 linear ft of a 3\/8 in wide x 1 in deep saw cut, or about 35 linear ft at 1-1\/2 in deep. It bonds to cured asphalt and concrete. Shelf life is 12 months at room temperature.\u003c\/p\u003e\u003ch4\u003eWhat's Included\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e1 gallon can of P-606 sealer\u003c\/li\u003e\n\u003cli\u003e2 tubes of liquid hardener\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\u003cli\u003eThis sealant is discontinued. Durant STAT-A-FLEX and ProSeal 6006 are the current gallon loop sealants.\u003c\/li\u003e\u003c\/ul\u003e","brand":"Bondo \/ 3M","offers":[{"title":"Default Title","offer_id":21951608451,"sku":"Bondo P606","price":65.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/bondo_p606.jpg?v=1699990010"},{"product_id":"q-seal-290-loop-sealant","title":"Q-Seal 290 Loop Sealant Black","description":"\u003cp\u003eChemque Q-Seal 290 is a one-part, moisture-curing polyurethane loop sealant in black, sold in a 30 fl oz cartridge. It seals loop wire saw cuts in asphalt and concrete with a waterproof, weather-resistant seal.\u003c\/p\u003e\u003cp\u003eQ-Seal 290 skins over in about 3 hours at 77°F and 50% relative humidity. It cures slower in colder weather and faster in warmer weather. The cured sealant resists de-icing salts, gasoline, hydraulic brake fluid, motor oil and 5% sodium chloride. Clean tools with Chemque S-235 solvent and hands with Q-CLEAN.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eApply between 36°F and 100°F to a dry, dust-free saw cut.\u003c\/li\u003e\n\u003cli\u003eThe 30 fl oz cartridge fits a manual or air-operated caulking gun. Bulk jobs use a pressurized pump system.\u003c\/li\u003e\n\u003cli\u003eShelf life is 1 year from the manufacture date.\u003c\/li\u003e\n\u003cli\u003eContains MDI. Use in a well-ventilated area and avoid skin and eye contact.\u003c\/li\u003e\n\u003cli\u003eShips by UPS Ground or LTL only, to US addresses.\u003c\/li\u003e\n\u003cli\u003eAlso sold in gray.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Chemque","offers":[{"title":"Default Title","offer_id":21951608771,"sku":"Q-Seal 290 Black","price":32.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/290.webp?v=1699990494"},{"product_id":"1-4-loop-backer-rod-sold-by-the-ft","title":"Backer Rod 1\/4\" Loop Backer Rod - (Sold by the FT)","description":"\u003cp\u003eThis is 1\/4 in foam backer rod for inductive loop installs. It is sold by the foot: order the quantity in feet. It comes as one continuous length cut to your order. Orders over 100 ft may come in more than one piece.\u003c\/p\u003e\u003cp\u003ePress the rod into the saw cut on top of the loop wire before you pour sealant. It holds the wire down at the bottom of the slot and fills part of the cut, so less sealant is needed.\u003c\/p\u003e\u003ch4\u003eFeatures\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e1\/4 in diameter\u003c\/li\u003e\n\u003cli\u003eSold by the foot\u003c\/li\u003e\n\u003cli\u003eHolds loop wire in the saw slot\u003c\/li\u003e\n\u003cli\u003eReduces the amount of sealant needed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003ePick a rod size that fits snug in your saw cut. The 3\/8 in rod is also listed.\u003c\/li\u003e\n\u003cli\u003eOrder enough to run the full loop perimeter plus the home run slot to the gate or curb.\u003c\/li\u003e\n\u003cli\u003eLoop wire, sealant and squeegee are listed separately.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Protec Controls","offers":[{"title":"Default Title","offer_id":21951609475,"sku":"BackerRod-1\/4","price":0.35,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/loop_backer_rod.jpg?v=1470156032"},{"product_id":"3-8-loop-backer-rod-sold-by-the-ft","title":"Backer Rod 3\/8\" Loop Backer Rod (Sold by the FT)","description":"\u003cp\u003eThis is 3\/8 in foam backer rod for inductive loop installs. It is sold by the foot: order the quantity in feet. It comes as one continuous length cut to your order. Orders over 100 ft may come in more than one piece.\u003c\/p\u003e\u003cp\u003ePress the rod into the saw cut on top of the loop wire before you pour sealant. It holds the wire down at the bottom of the slot and fills part of the cut, so less sealant is needed.\u003c\/p\u003e\u003ch4\u003eFeatures\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e3\/8 in diameter\u003c\/li\u003e\n\u003cli\u003eSold by the foot\u003c\/li\u003e\n\u003cli\u003eHolds loop wire in the saw slot\u003c\/li\u003e\n\u003cli\u003eReduces the amount of sealant needed\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003ePick a rod size that fits snug in your saw cut. The 1\/4 in rod is also listed.\u003c\/li\u003e\n\u003cli\u003eOrder enough to run the full loop perimeter plus the home run slot to the gate or curb.\u003c\/li\u003e\n\u003cli\u003eLoop wire, sealant and squeegee are listed separately.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Protec Controls","offers":[{"title":"Default Title","offer_id":21951610307,"sku":"BackerRod-3\/8","price":0.45,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/Backer-Rod_3cae6c77-dbbf-4b8d-96a1-f9a8e62a9909.jpeg?v=1465925614"},{"product_id":"16-xlpe-loop-wire-sold-by-the-10-16-gauge","title":"Loop Wire 16 awg XLPE - Sold by the foot (to nearest 10ft) (16 Gauge)","description":"\u003cp\u003eThis is 16 AWG stranded tinned copper loop wire with XLPE insulation, sold by the foot. XLPE holds up to oil and gasoline exposure and is rated to 125 °C, which makes it a better choice than THHN for saw-cut loops.\u003c\/p\u003e\u003cp\u003eUse it to build your own inductive loops for gate, barrier arm and parking lanes. Lay the turns in the saw cut, twist the lead-in, and run it back to the loop detector.\u003c\/p\u003e\u003ch4\u003eFeatures\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e16 AWG stranded tinned copper\u003c\/li\u003e\n\u003cli\u003eXLPE insulation, oil and gas resistant\u003c\/li\u003e\n\u003cli\u003eRated to 125 °C\u003c\/li\u003e\n\u003cli\u003eSold by the foot\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eSold by the foot, rounded to the nearest 10 ft: order the quantity in feet. Supplied as one continuous uncut piece up to 3500 ft.\u003c\/li\u003e\n\u003cli\u003eCount the turns your loop size needs, then add the lead-in length back to the detector.\u003c\/li\u003e\n\u003cli\u003eSee the Loop Size Chart in the Resources tab for turns and loop size.\u003c\/li\u003e\n\u003cli\u003eBacker rod and loop sealant are listed separately.\u003c\/li\u003e\n\u003cli\u003eFor larger jobs, the wire is also sold on 500 ft and 1000 ft spools.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Protec Controls","offers":[{"title":"Default Title","offer_id":21951611075,"sku":"XLPE-FT","price":0.3,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/1_df10e372-3e44-4e52-b21c-75eb94cd7a57.JPG?v=1469811464"},{"product_id":"direct-burial-paveover-loop-6-x-8","title":"BD LOOPS EL 28-60 PREFORMED DIRECT BURIAL LOOP 4' X 10' OR 6' X 8' w\/ 60' Lead","description":"\u003cp\u003eThe BD Loops EL 28-60 is a preformed direct burial inductance loop with a 28 ft perimeter (4 ft x 10 ft or 6 ft x 8 ft) and a 60 ft lead-in. The loop section is solid 16 AWG copper wire with PE insulation inside a doped PVC outer jacket, with 2 to 4 turns depending on loop and lead-in size. It goes under concrete, asphalt or pavers, or in gravel and dirt roads, for vehicle detection at gates and doors.\u003c\/p\u003e\u003cp\u003eThe solid wire holds its shape, so in a concrete pour the loop stays on top of the rebar. The lead-in conductors are bound inside the jacket, so there is no twisting. A flex yoke with a 1\/2 in coupler accepts PVC conduit for the lead-in run. There is no air pocket around the wire as with a loop pulled through PVC pipe, which cuts down on false detections from ground vibration. Each loop is tested 3 ways at the factory. The wire is rated for direct burial, 600 V and 167°F (75°C).\u003c\/p\u003e\u003ch4\u003eWhat's Included\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eOne BD Loops EL 28-60 preformed direct burial loop, 28 ft perimeter, with 60 ft lead-in attached\u003c\/li\u003e\n\u003cli\u003eCable ties\u003c\/li\u003e\n\u003cli\u003eGround stakes\u003c\/li\u003e\n\u003cli\u003eLead-in labels\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eConcrete: set the loop on top of the rebar or wire mesh, never below, offset from the pattern, and tie it down. Run the lead-in under the rebar.\u003c\/li\u003e\n\u003cli\u003ePavers or asphalt: lay the loop in a 2 in wide, 3 to 4 in deep trench. Under asphalt, keep at least 1\/8 in of sand between the loop and the hot asphalt. Gravel: bury it 7 to 10 in deep. BD Loops lists 14 in as the maximum depth.\u003c\/li\u003e\n\u003cli\u003eChoose the size by the area to cover (4 ft x 10 ft or 6 ft x 8 ft).\u003c\/li\u003e\n\u003cli\u003eThe 60 ft lead-in must reach the loop detector without a splice. Run it in 1\/2 in Schedule 40 or 80 rigid PVC with glued joints.\u003c\/li\u003e\n\u003cli\u003eA vehicle loop detector is required and is not included.\u003c\/li\u003e\n\u003cli\u003eKeep the loop 4 ft from the gate or door and 4 ft from other loops. Detection height is about 2\/3 of the loop's short side.\u003c\/li\u003e\n\u003cli\u003eRL part numbers have a 40 ft lead-in and EL part numbers have a 60 or 100 ft lead-in. BD Loops lists RL for residential and EL for commercial installs.\u003c\/li\u003e\n\u003cli\u003eFor saw-cut slots in existing pavement, use a BD Loops SC saw-cut loop instead.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"BD Loops","offers":[{"title":"Default Title","offer_id":21951612867,"sku":"EL 28-60","price":148.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/BD_Direct_Burial_Loop-1_1024x1024_eede2d59-143a-4a22-bf3c-44fae75dc8c4.webp?v=1693337732"},{"product_id":"direct-burial-paveover-loop-6-x-16","title":"BD LOOPS EL 44-60 PREFORMED DIRECT BURIAL 6' X 16' w\/ 60' LEAD","description":"\u003cp\u003eThe BD Loops EL 44-60 is a preformed direct burial inductance loop with a 44 ft perimeter (6 ft x 16 ft) and a 60 ft lead-in. The loop section is solid 16 AWG copper wire with PE insulation inside a doped PVC outer jacket, with 2 to 4 turns depending on loop and lead-in size. It goes under concrete, asphalt or pavers, or in gravel and dirt roads, for vehicle detection at gates and doors.\u003c\/p\u003e\u003cp\u003eThe solid wire holds its shape, so in a concrete pour the loop stays on top of the rebar. The lead-in conductors are bound inside the jacket, so there is no twisting. A flex yoke with a 1\/2 in coupler accepts PVC conduit for the lead-in run. There is no air pocket around the wire as with a loop pulled through PVC pipe, which cuts down on false detections from ground vibration. Each loop is tested 3 ways at the factory. The wire is rated for direct burial, 600 V and 167°F (75°C).\u003c\/p\u003e\u003ch4\u003eWhat's Included\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eOne BD Loops EL 44-60 preformed direct burial loop, 44 ft perimeter, with 60 ft lead-in attached\u003c\/li\u003e\n\u003cli\u003eCable ties\u003c\/li\u003e\n\u003cli\u003eGround stakes\u003c\/li\u003e\n\u003cli\u003eLead-in labels\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eConcrete: set the loop on top of the rebar or wire mesh, never below, offset from the pattern, and tie it down. Run the lead-in under the rebar.\u003c\/li\u003e\n\u003cli\u003ePavers or asphalt: lay the loop in a 2 in wide, 3 to 4 in deep trench. Under asphalt, keep at least 1\/8 in of sand between the loop and the hot asphalt. Gravel: bury it 7 to 10 in deep. BD Loops lists 14 in as the maximum depth.\u003c\/li\u003e\n\u003cli\u003eChoose the size by the area to cover (6 ft x 16 ft).\u003c\/li\u003e\n\u003cli\u003eThe 60 ft lead-in must reach the loop detector without a splice. Run it in 1\/2 in Schedule 40 or 80 rigid PVC with glued joints.\u003c\/li\u003e\n\u003cli\u003eA vehicle loop detector is required and is not included.\u003c\/li\u003e\n\u003cli\u003eKeep the loop 4 ft from the gate or door and 4 ft from other loops. Detection height is about 2\/3 of the loop's short side.\u003c\/li\u003e\n\u003cli\u003eRL part numbers have a 40 ft lead-in and EL part numbers have a 60 or 100 ft lead-in. BD Loops lists RL for residential and EL for commercial installs.\u003c\/li\u003e\n\u003cli\u003eFor saw-cut slots in existing pavement, use a BD Loops SC saw-cut loop instead.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"BD Loops","offers":[{"title":"Default Title","offer_id":21951613123,"sku":"EL 44-60","price":183.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/BD_Direct_Burial_Loop-1_808e3e6a-06c0-4678-8a0e-621462786cdf.jpg?v=1694127360"},{"product_id":"direct-burial-paveover-loop-6-x-20","title":"BD LOOPS RL 52-40 PREFORMED DIRECT BURIAL LOOP 6' X 20' w\/ 40' LEAD","description":"\u003cp\u003eThe BD Loops RL 52-40 is a preformed direct burial inductance loop with a 52 ft perimeter (6 ft x 20 ft) and a 40 ft lead-in. The loop section is solid 16 AWG copper wire with PE insulation inside a doped PVC outer jacket, with 2 to 4 turns depending on loop and lead-in size. It goes under concrete, asphalt or pavers, or in gravel and dirt roads, for vehicle detection at gates and doors.\u003c\/p\u003e\u003cp\u003eThe solid wire holds its shape, so in a concrete pour the loop stays on top of the rebar. The lead-in conductors are bound inside the jacket, so there is no twisting. A flex yoke with a 1\/2 in coupler accepts PVC conduit for the lead-in run. There is no air pocket around the wire as with a loop pulled through PVC pipe, which cuts down on false detections from ground vibration. Each loop is tested 3 ways at the factory. The wire is rated for direct burial, 600 V and 167°F (75°C).\u003c\/p\u003e\u003ch4\u003eWhat's Included\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eOne BD Loops RL 52-40 preformed direct burial loop, 52 ft perimeter, with 40 ft lead-in attached\u003c\/li\u003e\n\u003cli\u003eCable ties\u003c\/li\u003e\n\u003cli\u003eGround stakes\u003c\/li\u003e\n\u003cli\u003eLead-in labels\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eConcrete: set the loop on top of the rebar or wire mesh, never below, offset from the pattern, and tie it down. Run the lead-in under the rebar.\u003c\/li\u003e\n\u003cli\u003ePavers or asphalt: lay the loop in a 2 in wide, 3 to 4 in deep trench. Under asphalt, keep at least 1\/8 in of sand between the loop and the hot asphalt. Gravel: bury it 7 to 10 in deep. BD Loops lists 14 in as the maximum depth.\u003c\/li\u003e\n\u003cli\u003eChoose the size by the area to cover (6 ft x 20 ft).\u003c\/li\u003e\n\u003cli\u003eThe 40 ft lead-in must reach the loop detector without a splice. Run it in 1\/2 in Schedule 40 or 80 rigid PVC with glued joints.\u003c\/li\u003e\n\u003cli\u003eA vehicle loop detector is required and is not included.\u003c\/li\u003e\n\u003cli\u003eKeep the loop 4 ft from the gate or door and 4 ft from other loops. Detection height is about 2\/3 of the loop's short side.\u003c\/li\u003e\n\u003cli\u003eRL part numbers have a 40 ft lead-in and EL part numbers have a 60 or 100 ft lead-in. BD Loops lists RL for residential and EL for commercial installs.\u003c\/li\u003e\n\u003cli\u003eFor saw-cut slots in existing pavement, use a BD Loops SC saw-cut loop instead.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"BD Loops","offers":[{"title":"Default Title","offer_id":21951614147,"sku":"RL 52-40","price":179.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/BD_Direct_Burial_Loop-1_c6857c50-6a5f-4df4-8874-c9cb19eff753.jpg?v=1694141779"},{"product_id":"loop-sealant-squeegee","title":"Loop Sealant Squeegee","description":"\u003cp\u003eThis is a heavy-duty V-shaped squeegee for striking off loop sealant. It has a 36 in solid oak handle so you can work standing up, and a replaceable rubber blade.\u003c\/p\u003e\u003cp\u003eAfter you pour sealant into the loop saw cut, pull the V blade along the slot to clear excess sealant from the pavement and leave a flush finish.\u003c\/p\u003e\u003ch4\u003eFeatures\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eV-shaped blade\u003c\/li\u003e\n\u003cli\u003e36 in solid oak handle\u003c\/li\u003e\n\u003cli\u003eReplaceable rubber blade\u003c\/li\u003e\n\u003cli\u003eWork from a standing position\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eReplacement blades are listed separately as the Replacement Sealant Squeegee Blade.\u003c\/li\u003e\n\u003cli\u003eLoop sealant, backer rod and loop wire are listed separately.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Protec Controls","offers":[{"title":"Default Title","offer_id":21952233923,"sku":"PS-RV-GUM","price":99.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/Squeegee.jpeg?v=1465926216"},{"product_id":"loop-wire-pizza-wheel-with-corner-wedge","title":"Loop Wire Pizza Wheel with Corner Wedge","description":"\u003cp\u003eThe BD Loops PR-3\/16 is a saw-cut loop installation kit built around a 1\/8 in wide PVC pizza wheel. Roll the wheel along the groove to push loop wire down into a 3\/16 in saw cut without nicking the jacket. The wheel accepts a 3\/4 in PVC handle of any length.\u003c\/p\u003e\u003cp\u003eThe flat aluminum wedge tool, a 135 degree wedge, pushes wire into the dog-ear corner cuts. The metal clean-out hook pulls stubborn rocks and debris from the slot before the wire goes in. The wood dog-ear corner block marks the 5-1\/2 in x 5-1\/2 in x 7-3\/4 in corner cutting pattern.\u003c\/p\u003e\u003ch4\u003eWhat's Included\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e1\/8 in wide PVC pizza wheel with 3\/4 in PVC coupler\u003c\/li\u003e\n\u003cli\u003eFlat aluminum wedge tool\u003c\/li\u003e\n\u003cli\u003eMetal clean-out hook\u003c\/li\u003e\n\u003cli\u003eWood dog-ear corner block\u003c\/li\u003e\n\u003cli\u003eConstruction crayon\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eHandle not included. Supply your own length of 3\/4 in PVC conduit; BD Loops suggests Schedule 80.\u003c\/li\u003e\n\u003cli\u003eWorks in saw cuts up to 2-1\/4 in deep.\u003c\/li\u003e\n\u003cli\u003eSized for 3\/16 in saw cuts and BD Loops 3\/16 in preformed saw-cut loops.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"BD Loops","offers":[{"title":"Default Title","offer_id":21952234883,"sku":"PR-3\/16","price":119.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/BD_PR3-16_PizzaWheelWedgeTool.jpg?v=1696121831"},{"product_id":"emx-sp-24-surface-mounted-loop-pad","title":"EMX SP-24 Surface Mount Loop","description":"\u003cp\u003eThe EMX SP-24 is a surface-mounted inductive loop pad for automated carwash systems. It mounts between the guide rails and connects to a vehicle loop detector. With an EMX loop detector it detects vehicles up to 30 in above the pad.\u003c\/p\u003e\u003cp\u003eThe pad is sealed black polypropylene, 23.75 in x 23.75 in x 1 in, and stands up to carwash detergents. It has a 50 ft lead-in and four mounting holes. EMX warranty is 2 years.\u003c\/p\u003e\u003ch4\u003eWhat's Included\u003c\/h4\u003e\u003cul\u003e\u003cli\u003eSP-24 surface loop pad with 50 ft lead-in\u003c\/li\u003e\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eA vehicle loop detector is required.\u003c\/li\u003e\n\u003cli\u003eThe bolt-down wire guard (24 in x 3 in x 0.5 in) that covers the lead wire is optional and not included.\u003c\/li\u003e\n\u003cli\u003eMount the pad where it will not be driven over or struck. Tires or objects hitting the pad can cause false detects or damage it.\u003c\/li\u003e\n\u003cli\u003eMounting hardware is not listed by EMX.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EMX","offers":[{"title":"Default Title","offer_id":21952289795,"sku":"SP-24","price":649.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/emx_sp-24.png?v=1470681144"},{"product_id":"emx-lite-preformed-loop-2-x-6","title":"EMX PR-26 Lite Preformed Loop - 2' x 6' w\/ 50' Lead","description":"\u003cp\u003eThe EMX PR-26 is a PR Lite preformed inductive loop, 2 ft x 6 ft, with 50 ft of lead-in attached. It connects to a vehicle loop detector and works with EMX loop detectors. It goes in a saw cut in existing concrete or asphalt, or is tied in place before a new concrete slab is poured.\u003c\/p\u003e\u003cp\u003eThe loop wire is stranded conductors with XLP thermoplastic elastomer insulation inside flexible nonmetallic TPE tubing, 0.26 in outside diameter. Lightning protection is built in. The 50 ft lead-in is twisted and jacketed. Operating temperature is -4°F to 194°F (-20°C to 90°C). EMX warranty is 2 years.\u003c\/p\u003e\u003ch4\u003eWhat's Included\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e2 ft x 6 ft PR Lite preformed loop\u003c\/li\u003e\n\u003cli\u003e50 ft twisted, jacketed lead-in, attached\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eA vehicle loop detector is required. The loop does not detect on its own.\u003c\/li\u003e\n\u003cli\u003eExisting concrete: EMX calls for a 1 in deep saw cut with 45° cuts at the corners, backer material over the loop, then loop sealant.\u003c\/li\u003e\n\u003cli\u003eAsphalt: EMX calls for a 3\/4 in deep saw cut, sand packed over the loop, then new asphalt.\u003c\/li\u003e\n\u003cli\u003eNew concrete: tie the loop to a 1-1\/4 in PVC pipe frame and keep it separate from the rebar.\u003c\/li\u003e\n\u003cli\u003eMeasure the run from the loop to the detector. This listing has a 50 ft lead-in. Also listed with a 100 ft lead-in as the PR-26-100.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EMX","offers":[{"title":"Default Title","offer_id":21952289987,"sku":"PR-26","price":145.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/PRloop.png?v=1774283907"},{"product_id":"emx-lite-preformed-loop-4-x-6","title":"EMX PR-46 Lite Preformed Loop 4' x 6' w\/ 50' Lead","description":"\u003cp\u003eThe EMX PR-46 is a PR Lite preformed inductive loop, 4 ft x 6 ft, with 50 ft of lead-in attached. It connects to a vehicle loop detector and works with EMX loop detectors. It goes in a saw cut in existing concrete or asphalt, or is tied in place before a new concrete slab is poured.\u003c\/p\u003e\u003cp\u003eThe loop wire is stranded conductors with XLP thermoplastic elastomer insulation inside flexible nonmetallic TPE tubing, 0.26 in outside diameter. Lightning protection is built in. The 50 ft lead-in is twisted and jacketed. Operating temperature is -4°F to 194°F (-20°C to 90°C). EMX warranty is 2 years.\u003c\/p\u003e\u003ch4\u003eWhat's Included\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e4 ft x 6 ft PR Lite preformed loop\u003c\/li\u003e\n\u003cli\u003e50 ft twisted, jacketed lead-in, attached\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eA vehicle loop detector is required. The loop does not detect on its own.\u003c\/li\u003e\n\u003cli\u003eExisting concrete: EMX calls for a 1 in deep saw cut with 45° cuts at the corners, backer material over the loop, then loop sealant.\u003c\/li\u003e\n\u003cli\u003eAsphalt: EMX calls for a 3\/4 in deep saw cut, sand packed over the loop, then new asphalt.\u003c\/li\u003e\n\u003cli\u003eNew concrete: tie the loop to a 1-1\/4 in PVC pipe frame and keep it separate from the rebar.\u003c\/li\u003e\n\u003cli\u003eMeasure the run from the loop to the detector. This listing has a 50 ft lead-in. Also listed with a 100 ft lead-in as the PR-46-100.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EMX","offers":[{"title":"Default Title","offer_id":21952291203,"sku":"PR-46","price":150.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/PRloop.png?v=1774283907"},{"product_id":"emx-lite-preformed-loop-4-x-8","title":"EMX PR-48 Lite Preformed Loop 4' x 8' w\/ 50'  Lead","description":"\u003cp\u003eThe EMX PR-48 is a PR Lite preformed inductive loop, 4 ft x 8 ft, with 50 ft of lead-in attached. It connects to a vehicle loop detector and works with EMX loop detectors. It goes in a saw cut in existing concrete or asphalt, or is tied in place before a new concrete slab is poured.\u003c\/p\u003e\u003cp\u003eThe loop wire is stranded conductors with XLP thermoplastic elastomer insulation inside flexible nonmetallic TPE tubing, 0.26 in outside diameter. Lightning protection is built in. The 50 ft lead-in is twisted and jacketed. Operating temperature is -4°F to 194°F (-20°C to 90°C). EMX warranty is 2 years.\u003c\/p\u003e\u003ch4\u003eWhat's Included\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e4 ft x 8 ft PR Lite preformed loop\u003c\/li\u003e\n\u003cli\u003e50 ft twisted, jacketed lead-in, attached\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eA vehicle loop detector is required. The loop does not detect on its own.\u003c\/li\u003e\n\u003cli\u003eExisting concrete: EMX calls for a 1 in deep saw cut with 45° cuts at the corners, backer material over the loop, then loop sealant.\u003c\/li\u003e\n\u003cli\u003eAsphalt: EMX calls for a 3\/4 in deep saw cut, sand packed over the loop, then new asphalt.\u003c\/li\u003e\n\u003cli\u003eNew concrete: tie the loop to a 1-1\/4 in PVC pipe frame and keep it separate from the rebar.\u003c\/li\u003e\n\u003cli\u003eMeasure the run from the loop to the detector. This listing has a 50 ft lead-in. Also listed with a 100 ft lead-in as the PR-48-100.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EMX","offers":[{"title":"Default Title","offer_id":21952291779,"sku":"PR-48","price":155.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/PRloop.png?v=1774283907"},{"product_id":"emx-lite-preformed-loop-4-x-10","title":"EMX PR-410-100 Lite Preformed Loop 4' x 10' w\/ 100' Lead","description":"\u003cp\u003eThe EMX PR-410-100 is a PR Lite preformed inductive loop, 4 ft x 10 ft, with 100 ft of lead-in attached. It connects to a vehicle loop detector and works with EMX loop detectors. It goes in a saw cut in existing concrete or asphalt, or is tied in place before a new concrete slab is poured.\u003c\/p\u003e\u003cp\u003eThe loop wire is stranded conductors with XLP thermoplastic elastomer insulation inside flexible nonmetallic TPE tubing, 0.26 in outside diameter. Lightning protection is built in. The 100 ft lead-in is twisted and jacketed. Operating temperature is -4°F to 194°F (-20°C to 90°C). EMX warranty is 2 years.\u003c\/p\u003e\u003ch4\u003eWhat's Included\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e4 ft x 10 ft PR Lite preformed loop\u003c\/li\u003e\n\u003cli\u003e100 ft twisted, jacketed lead-in, attached\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eA vehicle loop detector is required. The loop does not detect on its own.\u003c\/li\u003e\n\u003cli\u003eExisting concrete: EMX calls for a 1 in deep saw cut with 45° cuts at the corners, backer material over the loop, then loop sealant.\u003c\/li\u003e\n\u003cli\u003eAsphalt: EMX calls for a 3\/4 in deep saw cut, sand packed over the loop, then new asphalt.\u003c\/li\u003e\n\u003cli\u003eNew concrete: tie the loop to a 1-1\/4 in PVC pipe frame and keep it separate from the rebar.\u003c\/li\u003e\n\u003cli\u003eMeasure the run from the loop to the detector. This listing has a 100 ft lead-in. Also listed with a 50 ft lead-in as the PR-410.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EMX","offers":[{"title":"Default Title","offer_id":21952292419,"sku":"PR-410-100","price":186.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/PRloop.png?v=1774283907"},{"product_id":"emx-lite-preformed-loop-8-x-12","title":"EMX PR-812 Lite Preformed Loop 8' x 12' w\/ 50' Lead","description":"\u003cp\u003eThe EMX PR-812 is a PR Lite preformed inductive loop, 8 ft x 12 ft, with 50 ft of lead-in attached. It connects to a vehicle loop detector and works with EMX loop detectors. It goes in a saw cut in existing concrete or asphalt, or is tied in place before a new concrete slab is poured.\u003c\/p\u003e\u003cp\u003eThe loop wire is stranded conductors with XLP thermoplastic elastomer insulation inside flexible nonmetallic TPE tubing, 0.26 in outside diameter. Lightning protection is built in. The 50 ft lead-in is twisted and jacketed. Operating temperature is -4°F to 194°F (-20°C to 90°C). EMX warranty is 2 years.\u003c\/p\u003e\u003ch4\u003eWhat's Included\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e8 ft x 12 ft PR Lite preformed loop\u003c\/li\u003e\n\u003cli\u003e50 ft twisted, jacketed lead-in, attached\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eA vehicle loop detector is required. The loop does not detect on its own.\u003c\/li\u003e\n\u003cli\u003eExisting concrete: EMX calls for a 1 in deep saw cut with 45° cuts at the corners, backer material over the loop, then loop sealant.\u003c\/li\u003e\n\u003cli\u003eAsphalt: EMX calls for a 3\/4 in deep saw cut, sand packed over the loop, then new asphalt.\u003c\/li\u003e\n\u003cli\u003eNew concrete: tie the loop to a 1-1\/4 in PVC pipe frame and keep it separate from the rebar.\u003c\/li\u003e\n\u003cli\u003eMeasure the run from the loop to the detector. This listing has a 50 ft lead-in. Also listed with a 100 ft lead-in as the PR-812-100.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EMX","offers":[{"title":"Default Title","offer_id":21952292739,"sku":"PR-812","price":174.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/PRloop.png?v=1774283907"},{"product_id":"emx-lite-preformed-loop-6-x-10","title":"EMX PR-610 Lite Preformed Loop 6' x 10' w\/ 50' Lead","description":"\u003cp\u003eThe EMX PR-610 is a PR Lite preformed inductive loop, 6 ft x 10 ft, with 50 ft of lead-in attached. It connects to a vehicle loop detector and works with EMX loop detectors. It goes in a saw cut in existing concrete or asphalt, or is tied in place before a new concrete slab is poured.\u003c\/p\u003e\u003cp\u003eThe loop wire is stranded conductors with XLP thermoplastic elastomer insulation inside flexible nonmetallic TPE tubing, 0.26 in outside diameter. Lightning protection is built in. The 50 ft lead-in is twisted and jacketed. Operating temperature is -4°F to 194°F (-20°C to 90°C). EMX warranty is 2 years.\u003c\/p\u003e\u003ch4\u003eWhat's Included\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e6 ft x 10 ft PR Lite preformed loop\u003c\/li\u003e\n\u003cli\u003e50 ft twisted, jacketed lead-in, attached\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eA vehicle loop detector is required. The loop does not detect on its own.\u003c\/li\u003e\n\u003cli\u003eExisting concrete: EMX calls for a 1 in deep saw cut with 45° cuts at the corners, backer material over the loop, then loop sealant.\u003c\/li\u003e\n\u003cli\u003eAsphalt: EMX calls for a 3\/4 in deep saw cut, sand packed over the loop, then new asphalt.\u003c\/li\u003e\n\u003cli\u003eNew concrete: tie the loop to a 1-1\/4 in PVC pipe frame and keep it separate from the rebar.\u003c\/li\u003e\n\u003cli\u003eMeasure the run from the loop to the detector. This listing has a 50 ft lead-in. Also listed with a 100 ft lead-in as the PR-610-100.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EMX","offers":[{"title":"Default Title","offer_id":21952292867,"sku":"PR-610","price":165.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/PRloop.png?v=1774283907"},{"product_id":"diablo-controls-dsp-7-micro-loop-detector","title":"Diablo Controls DSP-7 Micro Loop Detector","description":"\u003cp\u003eThe Diablo Controls DSP-7 is a single channel loop detector with one relay output (NO and NC contacts, 1 A max) and a removable 7-pin terminal block. It runs on 10 to 30 VDC or 10 to 28 VAC and draws about 35 mA with no vehicle on the loop. It is 1.52 x 2.9 x 1.56 in.\u003c\/p\u003e\u003cp\u003eThere are no switches to set. The detector adjusts itself for loop and lead-in size and does not cross-talk with other Diablo detectors of this type. The green LED blinks once a second in normal operation, slowly for an open loop and fast for a shorted loop; the red LED shows detect. Fail-safe: the output goes to detect if the loop fails, so it can be used on a safety loop. Loop inductance range is 20 to 2000 µH. It operates from -35°F to 165°F.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eFail-safe. The DSP-7LP is the low power version for solar gates; the DSP-6LP is the fail-secure low power version.\u003c\/li\u003e\n\u003cli\u003eTerminal block wiring: relay NC, common and NO on pins 1 to 3, power on pins 4 and 5, loop on pins 6 and 7.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Diablo Controls","offers":[{"title":"Default Title","offer_id":21952334403,"sku":"DSP-7","price":86.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/DSP-7.jpg?v=1697660579"},{"product_id":"edi-lma-100-loop-detector","title":"EDI LMA-100-LV Loop Detector ***Discontinued - Unavailable***","description":"\u003cp\u003eDiscontinued by EDI. The LMA-1250-LV is the updated version. The LMA-100-LV is a single channel, single output loop detector with one relay (NO and NC contacts) and an 11-pin connector. It runs on 12 VDC, 24 VDC or 24 VAC (10 to 40 VDC or 14 to 35 VAC).\u003c\/p\u003e\u003cp\u003eDIP switches set four sensitivity levels, four loop frequencies, sensitivity boost, Limited or Infinite Presence, and the output mode: presence, or a 250 ms pulse on entry or on exit. A power loss of 4 seconds or less does not drop a call. LED flash patterns show open loops, shorted loops and inductance changes over 25%, and the last fault is kept in memory. It operates from -30°F to 165°F.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eNo longer made. The LMA-1250-LV is an 11-pin plug-in detector that adds a second relay and the DEFLECTOMETER display.\u003c\/li\u003e\n\u003cli\u003eThe LMA-100-HV was the 120 to 240 VAC version.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EDI - Eberle Design Inc","offers":[{"title":"Default Title","offer_id":21952338499,"sku":"LMA-100-LV","price":99.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/LMA100.jpg?v=1698160544"},{"product_id":"edi-lma-200-loop-detector","title":"EDI LMA-200-LV Loop Detector ***Discontinued - Unavailable***","description":"\u003cp\u003eDiscontinued by EDI. The LMA-1250-LV is the updated version. The LMA-200-LV is a single channel loop detector with two relay outputs and an 11-pin connector. It runs on 12 VDC, 24 VDC or 24 VAC (10 to 40 VDC or 14 to 35 VAC).\u003c\/p\u003e\u003cp\u003eOutput A is presence. Output B is set by DIP switches for a 250 ms pulse on entry, pulse on exit, a duplicate of Output A, or on during a loop fault. It has four loop frequencies, four sensitivity levels, sensitivity boost, Limited or Infinite Presence and a front panel reset. A power loss of 4 seconds or less does not drop a call. Open loops, shorted loops and inductance changes over 25% are flagged and kept in fault memory. It operates from -30°F to 165°F.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eNo longer made. The LMA-1250-LV has the same output functions and adds the DEFLECTOMETER display and 10 sensitivity levels.\u003c\/li\u003e\n\u003cli\u003eThe LMA-200-HV was the 120 to 240 VAC version.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EDI - Eberle Design Inc","offers":[{"title":"Default Title","offer_id":21952340035,"sku":"LMA-200-LV","price":99.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/LMA-200.jpeg?v=1465926311"},{"product_id":"edi-lma-1250-loop-detector","title":"EDI LMA-1250-LV Loop Detector","description":"\u003cp\u003eThe EDI LMA-1250-LV is a single channel DEFLECTOMETER loop detector with two relay outputs and a rear 11-pin male Amphenol connector (86CP11). It runs on 12 VDC, 24 VDC or 24 VAC (10 to 40 VDC or 14 to 35 VAC). The housing is 2.875 x 1.375 x 3.0625 in.\u003c\/p\u003e\u003cp\u003eThe 7-segment DEFLECTOMETER display reads out the detection level, so sensitivity can be set to pick up all vehicles, including motorcycles. It also shows loop frequency and fault codes. Output A runs Limited or Infinite Presence. Output B gives a 250 ms pulse on entry or exit, duplicates Output A, or signals a fault. There are 10 sensitivity levels, four loop frequencies, a 2 second delay and 2, 5 or 10 second extension. Relays are rated 5 A. Loop inductance range is 20 to 2500 µH. It operates from -30°F to 165°F.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eFail-safe: on a loop fault or power loss, Relay A closes Common to NO.\u003c\/li\u003e\n\u003cli\u003eReplaces the discontinued EDI LMA-100-LV, LMA-200-LV and LMA-1150-LV. The LMA-1250-HV is the 120 to 240 VAC version.\u003c\/li\u003e\n\u003cli\u003eWires with a standard 11-pin harness or socket base.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EDI - Eberle Design Inc","offers":[{"title":"Default Title","offer_id":21952341507,"sku":"LMA-1250-LV","price":99.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/LMA1250_49a3ec1a-d5f6-472b-9a2c-9d9f8b07a2a8.jpg?v=1698159868"},{"product_id":"edi-lma-1250-lp-loop-detector","title":"EDI LMA-1250-LP Loop Detector ***Discontinued - Unavailable***","description":"\u003cp\u003eDiscontinued by EDI. The LMA-1250-LP is a low power version of the LMA-1250 DEFLECTOMETER loop detector, for battery or solar powered gates. It runs on 10 to 40 VDC (12 or 24 VDC nominal) and draws about 4 mA at 12 VDC with no vehicle and the display off. It has two relay outputs and a rear 11-pin male Amphenol connector (86CP11). The housing is 2.875 x 1.375 x 3.0625 in.\u003c\/p\u003e\u003cp\u003eOutput A runs Limited or Infinite Presence with 0, 2, 5 or 10 second extension, and is set for fail-safe or fail-secure. Output B gives a 250 ms pulse on entry or exit, duplicates Output A, or turns on during a loop fault. The DEFLECTOMETER display, 10 sensitivity levels, four loop frequencies, 2 second delay and non-volatile fault memory carry over from the LMA-1250. Relays are rated 5 A. Loop inductance range is 20 to 2500 µH. It operates from -30°F to 165°F.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eNo longer made. EDI does not name a direct replacement.\u003c\/li\u003e\n\u003cli\u003eDC only. EDI notes its performance differs from the standard LMA-1250; use it only where low current draw matters.\u003c\/li\u003e\n\u003cli\u003eFor 10-pin Molex operator ports, the LMA-1800-LP is EDI's low power plug-in detector.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EDI - Eberle Design Inc","offers":[{"title":"Default Title","offer_id":21952342083,"sku":"LMA-1250-LP","price":99.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/1250lp_00f205c5-7179-478f-b53f-9f9299a662dd.png?v=1470424644"},{"product_id":"keypad-lightning-surge-suppressor","title":"Keypad Lightning\/Surge Suppressor","description":"\u003cp\u003eThis is a lightning and surge suppressor for keypad wiring at a gate or door. It goes between the keypad wiring and the gate operator or door control and needs an earth ground to work.\u003c\/p\u003e\u003cp\u003eIt protects the operator or door circuitry from surges that come in on the keypad wires. It does not protect the keypad itself. A standard standalone keypad needs two: one on the power wires and one on the relay output wires.\u003c\/p\u003e\u003ch4\u003eFeatures\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eProtects gate operator or door circuitry\u003c\/li\u003e\n\u003cli\u003eFor keypad power or relay wiring\u003c\/li\u003e\n\u003cli\u003eRequires earth ground\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eOrder two for a standard standalone keypad: one for power, one for relay wires.\u003c\/li\u003e\n\u003cli\u003eDrive a ground rod or bond to a proper earth ground. Better grounding gives better protection.\u003c\/li\u003e\n\u003cli\u003eThis does not protect the keypad. Protect the keypad itself separately if needed.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Protec Controls","offers":[{"title":"Default Title","offer_id":21952754371,"sku":null,"price":39.59,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/Loop_2eed863a-884d-4b56-8ace-dc3c2f4e5528.jpeg?v=1465926672"},{"product_id":"diablo-controls-dsp-40s-loop-detector","title":"Diablo Controls DSP-40S Loop Detector","description":"\u003cp\u003eThe Diablo Controls DSP-40S is a single channel plug-in loop detector with solid-state detect and fail outputs and a 10-position Molex connector (type 09-48-1104) that mates with many 0.156 in pitch female headers on gate operators and access control boards. Diablo lists 10 to 30 V AC or DC on the power pins. It is 2.4 x 0.8 x 2.25 in.\u003c\/p\u003e\u003cp\u003eBoth outputs are open collector, 30 mA max sink, with transient protection. A single push button resets the detector and sets four sensitivity levels; the LEDs flash the current level after a reset. Detect memory holds a vehicle through power drops of about 1.5 seconds. Fail-safe operation. Loop inductance range is 20 to 2000 µH. It operates from -35°F to 165°F.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eFits Diablo RK-1R and RK-3R detector racks when a relay output is needed.\u003c\/li\u003e\n\u003cli\u003eSolid-state outputs only, 30 mA max. Check the input your controller expects.\u003c\/li\u003e\n\u003cli\u003ePinout: loop on pins 1 and 2, power on pins 3 or 9 and common on pin 10, fail output on pins 6 and 7, detect output on pin 8.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Diablo Controls","offers":[{"title":"Default Title","offer_id":21952792323,"sku":"DSP-40S","price":85.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/DSP-40S_92eb92dc-63e9-48b4-8c5c-0a01c3c3d16b.jpg?v=1697660175"},{"product_id":"diablo-controls-dsp-22-two-channel-loop-detector","title":"Diablo Controls DSP-22-2 Two Channel Plugin Loop Detector(Doorking)","description":"\u003cp\u003eThe Diablo Controls DSP-22-2 is a two channel plug-in loop detector for DoorKing gate operators. It plugs into the loop detector ports on the DoorKing control board and is a low power, direct replacement for the DoorKing 9409 and 9405 two channel detectors. It runs on 14 to 27 VDC and draws about 1.62 mA with neither channel in detect.\u003c\/p\u003e\u003cp\u003eChannel 1 has a solid-state open-drain output rated 250 mA at 30 V. Channel 2 has a relay with NO and NC contacts and can run presence or pulse. Each channel has four sensitivity settings and sensitivity boost on DIP switches. Channel 2 accepts the Diablo Free Exit Probe (mini-loop) and shows a flicker display during pulse detection. Loop monitoring and fault memory show current and past loop faults. Always fail-safe. Loop inductance range is 20 to 1500 µH. It operates from -35°F to 165°F.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eFor DoorKing operators with on-board detector ports. Replaces the DoorKing 9409 and 9405.\u003c\/li\u003e\n\u003cli\u003eThe DSP-22-1 is the single channel version (replaces DoorKing 9410).\u003c\/li\u003e\n\u003cli\u003eThe Free Exit Probe works in pulse mode only and must never be used as a safety or obstruction sensor.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Diablo Controls","offers":[{"title":"Default Title","offer_id":21952792899,"sku":"DSP-22-2","price":158.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/DPS-22.jpg?v=1697659815"},{"product_id":"diablo-controls-dsp-15-loop-detector","title":"Diablo Controls DSP-15-LVT Loop Detector - Terminal Block","description":"\u003cp\u003eThe Diablo Controls DSP-15-LVT is the PC board version of the DSP-10 series: a single channel loop detector with two relay outputs and a 10-pin pluggable screw terminal block. It runs on 10 to 30 VDC or 10 to 28 VAC, uses under 3 W, and the board is 2.90 x 4.125 in.\u003c\/p\u003e\u003cp\u003eRelays A and B are rated 3 A. Output A is set for fail-safe or fail-secure with a jumper. Output B runs true presence, entry pulse, exit pulse or loop fail. There are ten sensitivity levels, a 2 second delay, extension of 0, 2, 5 or 10 seconds, and sensitivity boost. The detector tunes itself and tracks environmental drift with Diablo's HYPERTRACK software. It rides through power drops of about 3 seconds, and is protected if connected to a higher voltage. Loop inductance range is 20 to 2000 µH. It operates from -35°F to 165°F.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eThis is the terminal block (LVT) version. DSP-15 versions: LVT (pluggable screw terminal block), LVM (10-pin male Molex), LVF (10-pin female Molex).\u003c\/li\u003e\n\u003cli\u003eCheck the board header or wiring in your control box before ordering.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Diablo Controls","offers":[{"title":"Default Title","offer_id":44400306749740,"sku":"DSP-15-LVT","price":174.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/DSP-15-T.jpg?v=1760971467"},{"product_id":"edi-lma-1150-hv-loop-detector","title":"EDI LMA 1150-HV Loop Detector ***Discontinued - Unavailable***","description":"\u003cp\u003eDiscontinued by EDI. The LMA-1250-HV is the updated version. The LMA-1150-HV is a single channel DEFLECTOMETER loop detector with one programmable relay output and a rear 11-pin male Amphenol connector (86CP11). It runs on 120 to 240 VAC (95 to 250 VAC, 50\/60 Hz). The housing is 2.875 x 1.375 x 3.0625 in.\u003c\/p\u003e\u003cp\u003eThe relay runs presence or a 250 ms pulse and is rated 5 A. The DEFLECTOMETER display shows the detection level, loop frequency and fault codes. It has 10 sensitivity levels, sensitivity boost, four loop frequencies, a 2 second delay, 2, 5 or 10 second extension, and call memory through power losses of 4 seconds or less. Fail-safe: on a loop fault or power loss, Common closes to NO. Loop inductance range is 20 to 2500 µH and lead-in can run up to 5,000 ft. It operates from -30°F to 165°F.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eNo longer made. The LMA-1250-HV uses the same housing and connector and adds a second relay output.\u003c\/li\u003e\n\u003cli\u003eThe LMA-1150-LV was the 12\/24 V AC\/DC version.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EDI - Eberle Design Inc","offers":[{"title":"Default Title","offer_id":21952821571,"sku":"LMA-1150-HV","price":99.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/LMA-1150.jpg?v=1698158926"},{"product_id":"edi-lma-1500-loop-detector","title":"EDI LMA-1500 Loop Detector ***Discontinued - LMA-1800 Will Be Shipped***","description":"\u003cp\u003eDiscontinued by EDI. The LMA-1800 is the updated version. The EDI LMA-1500 is a single channel DEFLECTOMETER loop detector that plugs into a gate operator's 10-pin Molex detector port. It has two programmable solid-state outputs and a rear 10-pin Molex connector (09-48-1104), and runs on 10 to 30 VDC or 14 to 26 VAC. The unit is 2.30 x 2.75 x 0.80 in.\u003c\/p\u003e\u003cp\u003eThe DEFLECTOMETER display shows the detection level so sensitivity can be set to catch all vehicles, including motorcycles. There are 10 sensitivity levels and four loop frequencies. Outputs are open collector, rated 100 mA at 30 VDC. Loop inductance range is 20 to 2500 µH. It operates from -30°F to 165°F.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003ePlugs into 10-pin Molex detector ports, including Chamberlain\/Elite SL3000 and CSW200; Advanced Access Automation CSL2000, CSW2000 and RSW1000; All-O-Matic SL100-DC, SL150DC, OH200DC, SW300DC and SW350DC; Intelligate IQ500 and IQ5000; Linear (OSCO) SL and SW with APeX controller; late SECOM operators with 10-pin Molex; Viking L-3, F-1, T-21, H-10, B-12 and Q-4.\u003c\/li\u003e\n\u003cli\u003eSolid-state outputs only. For relay contacts, use an 11-pin relay detector such as the LMA-1250.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EDI - Eberle Design Inc","offers":[{"title":"Default Title","offer_id":21952822403,"sku":"LMA-1500","price":99.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/LMA1500.jpg?v=1698161261"},{"product_id":"edi-lma-1500-lp-loop-detector","title":"EDI LMA-1500-LP Loop Detector ***Discontinued - LMA-1800-LP Will Be Shipped***","description":"\u003cp\u003eDiscontinued by EDI. The LMA-1800-LP is the updated version. The EDI LMA-1500-LP is a low power, single channel DEFLECTOMETER loop detector for solar and battery powered gate operators. It draws 8 mA max with no vehicle (9 mA max on a call). It has two programmable solid-state outputs and a rear 10-pin Molex connector (09-48-1104), and runs on 10 to 30 VDC or 14 to 26 VAC. The unit is 2.30 x 2.75 x 0.80 in.\u003c\/p\u003e\u003cp\u003eThe DEFLECTOMETER display shows the detection level so sensitivity can be set to catch all vehicles, including motorcycles. There are 10 sensitivity levels and four loop frequencies. Outputs are open collector, rated 100 mA at 30 VDC. Loop inductance range is 20 to 2500 µH. It operates from -30°F to 165°F.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003ePlugs into 10-pin Molex detector ports, including Chamberlain\/Elite SL3000 and CSW200; Advanced Access Automation CSL2000, CSW2000 and RSW1000; All-O-Matic SL100-DC, SL150DC, OH200DC, SW300DC and SW350DC; Intelligate IQ500 and IQ5000; Linear (OSCO) SL and SW with APeX controller; late SECOM operators with 10-pin Molex; Viking L-3, F-1, T-21, H-10, B-12 and Q-4.\u003c\/li\u003e\n\u003cli\u003eEDI notes the LP performs differently from the standard model. Use it where low current draw matters.\u003c\/li\u003e\n\u003cli\u003eSolid-state outputs only. For relay contacts, use an 11-pin relay detector such as the LMA-1250.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EDI - Eberle Design Inc","offers":[{"title":"Default Title","offer_id":21952823427,"sku":"LMA-1500-LP","price":99.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/1500LP.jpg?v=1698161524"},{"product_id":"edi-lma-1400-loop-detector","title":"EDI LMA-1400-M Loop Detector ***Discontinued***","description":"\u003cp\u003eDiscontinued by EDI. The LMA-1400-M is a single channel DEFLECTOMETER loop detector with two programmable relay outputs, fail-safe operation, and a 10-pin male Molex connector. It runs on 12 VDC to 24 VDC or 24 VAC.\u003c\/p\u003e\u003cp\u003eThe DEFLECTOMETER display helps set sensitivity. The detector flags open loops, shorted loops and inductance changes over 25%. It operates from -30°F to 165°F.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eNo longer made. EDI does not name a direct replacement.\u003c\/li\u003e\n\u003cli\u003eLMA-1400 family: -M relay, 10-pin male Molex; -MS solid-state, fail-secure, male Molex; -F and -FS female Molex; -B and -BS terminal block.\u003c\/li\u003e\n\u003cli\u003eFor 10-pin female Molex operator ports, the EDI LMA-1800 is the current plug-in detector. Check the connector gender and outputs your operator needs.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EDI - Eberle Design Inc","offers":[{"title":"Default Title","offer_id":21952823811,"sku":"LMA-1400-M","price":120.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/lma1400.jpg?v=1698161044"},{"product_id":"replacement-sealant-squeegee-blade","title":"Replacement Sealant Squeegee Blade","description":"\u003cp\u003eReplacement Sealant Squeegee Blade\u003c\/p\u003e\n\u003cp\u003eReplacement blade for the loop sealant squeegee!\u003c\/p\u003e\n\u003cp\u003eWe have 10 years experience working on these products in the field. Please contact us if we can be of any assistance!\u003c\/p\u003e","brand":"Kraft Tool","offers":[{"title":"Default Title","offer_id":21952829635,"sku":"GG813-02","price":16.74,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/SqueegeeBlade.jpeg?v=1465926735"},{"product_id":"reno-a-e-bx-lp-series-loop-detector","title":"Reno A\u0026E BX-LP Series Loop Detector ***Discontinued - Unavailable***","description":"\u003cp\u003eDiscontinued by Reno A\u0026amp;E. The BX-LP is a single channel, low power loop detector with two relay outputs and a rear 11-pin Amphenol connector. It runs on 12 VDC (10 to 12 VDC) and draws 1.1 to 5.5 mA with no vehicle on the loop, depending on the sensitivity setting. Reno A\u0026amp;E built the BX-LP series for solar and battery powered installs.\u003c\/p\u003e\u003cp\u003eOutput A runs Limited Presence or True Presence. Output B duplicates Output A, or gives a 250 ms pulse on entry or on exit. A 2 second call delay can be applied to both outputs. Eight sensitivity levels are set on a rotary switch, with four loop frequencies and a fail-safe or fail-secure setting for Output A. Relays are rated 6 A. The housing is 3.00 x 1.75 x 4.30 in, excluding the connector, and it operates from -30°F to 180°F.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eNo longer made by Reno A\u0026amp;E. EDI does not name a direct replacement.\u003c\/li\u003e\n\u003cli\u003eThis is the 12 VDC relay version. The BX-LP-24 was the 24 VDC version and the BX-LP-SS had solid-state outputs.\u003c\/li\u003e\n\u003cli\u003eWires with an 11-pin harness such as the Reno A\u0026amp;E LMH802-4.\u003c\/li\u003e\n\u003cli\u003eA standard BX detector draws much more current. Check the solar or battery budget before using one as a substitute.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Reno A\u0026E","offers":[{"title":"Default Title","offer_id":21952842563,"sku":"BX-LP","price":104.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/reno_ae_bx-lp.png?v=1470857032"},{"product_id":"reno-a-e-l-atg-series-loop-detector","title":"Reno A\u0026E L-ATG Series Loop Detector","description":"\u003cp\u003eThe Reno A\u0026amp;E L-ATG is a single channel anti-tailgating loop detector for parking and access control lanes. It counts passenger vehicles even when they run bumper to bumper and flags when more than one vehicle enters during a single gate cycle. Reno A\u0026amp;E rates count accuracy above 99% with standard 2.5 x 6 ft loops.\u003c\/p\u003e\u003cp\u003eRelay A carries the vehicle call with delay and extension timing. Relay B gives count, tailgate and entry pulses. The front panel LCD shows the running count up to 99,999. It has directional logic, loop fail monitoring with fail-safe operation, and a loop fail memory. The detector self-tunes within 2 seconds of power-up or reset. Relays are rated 6 A. The housing is 4.70 x 2.50 x 5.90 in, excluding the MS3102A-18-1P connector, and it operates from -40°F to 180°F.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eReno A\u0026amp;E makes three power versions: L-ATG-1 (120 VAC), L-ATG-5 (12 VDC, 24 VDC or 24 VAC) and L-ATG-35 (240 VAC). Confirm which one you need.\u003c\/li\u003e\n\u003cli\u003eUses a 10-pin MS style harness (Reno A\u0026amp;E 801-4 pinout), not an 11-pin socket.\u003c\/li\u003e\n\u003cli\u003eCount accuracy depends on loop size and layout. Follow the L-ATG instructions for loop placement.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Reno A\u0026E","offers":[{"title":"Default Title","offer_id":21952843203,"sku":"L-ATG","price":600.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/L-ATG_20Series.jpeg?v=1465926750"},{"product_id":"reno-a-e-h1-series-loop-detector","title":"RENO A\u0026E H1-12-F DETECTOR","description":"\u003cp\u003eThe Reno A\u0026amp;E H1-12-F is a single channel PC board loop detector with a 10-pin in-line female Molex connector (Molex 09-48-3105) centered on the 2.50 in side of the board. It runs on 12 VDC (10 to 14 VDC) at 21 mA max. The board is 2.50 x 2.75 x 0.85 in, excluding the connector.\u003c\/p\u003e\u003cp\u003eIt has three solid-state FET outputs. Output A is presence, set for fail-safe or fail-secure. Output B is presence or a 250 ms pulse on entry or on exit. The third output signals a loop fail. Delay and extend times are 0, 2, 5 or 10 seconds. Eight sensitivity levels are set on a rotary switch, with four loop frequencies, sensitivity boost and detect memory. Loop inductance range is 20 to 1000 µH. It operates from -30°F to 180°F.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eDirect plug-in replacement for the older Reno A\u0026amp;E H-12-F.\u003c\/li\u003e\n\u003cli\u003eF means female connector. Reno A\u0026amp;E also lists male (M) and low power (LP) versions.\u003c\/li\u003e\n\u003cli\u003e12 VDC only. Fits operator boards with a 10-pin Molex detector header; check the board pinout and supply first.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Reno A\u0026E","offers":[{"title":"Default Title","offer_id":21952843907,"sku":"H1-12-F","price":81.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/H1-12-F.jpg?v=1698683501"},{"product_id":"reno-a-e-h2-series-loop-detector","title":"RENO A\u0026E H2-12-F DETECTOR","description":"\u003cp\u003eThe Reno A\u0026amp;E H2-12-F is a single channel PC board loop detector with a 10-pin in-line female Molex connector centered on the 2.50 in side of the board. It runs on 10 to 14 VDC at 21 mA max. The board is 2.50 x 2.75 x 0.85 in, excluding the connector.\u003c\/p\u003e\u003cp\u003eIt has three solid-state FET outputs. Output A is presence, set for fail-safe or fail-secure. Output B is presence or a pulse on entry or on exit. The third output signals a loop fail. Delay and extend times are 0, 2, 5 or 10 seconds. Eight sensitivity levels are set on a rotary switch, with four loop frequencies on DIP switches, sensitivity boost and detect memory for power drops up to 2 seconds. The detector tunes itself within 2 seconds of power-up or reset. It operates from -30°F to 180°F.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003e12 VDC only. Check the operator board supply before installing.\u003c\/li\u003e\n\u003cli\u003eFits operator boards with a 10-pin Molex detector header.\u003c\/li\u003e\n\u003cli\u003eThe H1-12-F is the related Reno A\u0026amp;E board detector with the same connector position.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Reno A\u0026E","offers":[{"title":"Default Title","offer_id":21952846019,"sku":"H2-12-F","price":81.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/reno_ae_h2.png?v=1470857595"},{"product_id":"reno-a-e-k-series-loop-detector","title":"RENO A\u0026E K-24 VEHICLE LOOP DETECTOR ***Discontinued***","description":"\u003cp\u003eDiscontinued by Reno A\u0026amp;E. The K-24 is a single channel PC board loop detector with two relay outputs and a 10-pin in-line male Molex connector. It runs on 24 VAC (18 to 32 VAC, 4 W max). The board is 4.50 x 3.20 x 1.15 in.\u003c\/p\u003e\u003cp\u003eOutput A runs Limited Presence or True Presence. Output B duplicates Output A, or gives pulse on entry, pulse on exit or a fault output. Both relays have NO and NC contacts rated 6 A. Eight sensitivity levels are set on a rotary switch and four loop frequencies on DIP switches. It has a 2 second call delay, sensitivity boost, detect memory for power drops up to 2 seconds, and Power, Detect and Fail LEDs. It operates from -30°F to 180°F.\u003c\/p\u003e\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eNo longer made by Reno A\u0026amp;E.\u003c\/li\u003e\n\u003cli\u003e24 VAC version, fail-safe. Reno A\u0026amp;E also made a 120 VAC K-120 and fail-secure (S) versions.\u003c\/li\u003e\n\u003cli\u003eCheck the operator board's 10-pin Molex header and supply before fitting a different detector.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Reno A\u0026E","offers":[{"title":"Default Title","offer_id":21952850179,"sku":"K-24","price":99.0,"currency_code":"USD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/products\/reno_ae_k.png?v=1470857980"},{"product_id":"reno-a-e-plh-r-16-perimeter-preformed-loop","title":"Reno A\u0026E PLH-16-40-R EverLoop Rugged Preformed Loop - 3'x5' w\/ 40' Lead","description":"\u003cp\u003eThe Reno A\u0026amp;E PLH-16-40-R is a prefabricated inductive loop and lead-in assembly for direct burial in dirt or gravel. It is sized for a 3 ft x 5 ft rectangular loop (16 ft perimeter) with a 40 ft lead-in cable. The loop cable, lead-in and splice enclosure arrive joined and tested, so there are no field splices at the loop.\u003c\/p\u003e\n\u003cp\u003eThe high-visibility red outer jacket is Elexar 8451 thermoplastic elastomer (TPE) for abrasion resistance and flexibility in cold weather. Wire insulation and inner jackets are cross-linked polyethylene (XLPE), and the cables are filled with water block gel. The splice enclosure is high-impact, glass-impregnated plastic with soldered, sealed and tested connections. Reno A\u0026amp;E puts typical detection height at about 2\/3 of the shortest loop side, roughly 2 ft on this 3 ft wide loop. Covered by a 10-year limited warranty.\u003c\/p\u003e\n\u003ch4\u003eWhat's Included\u003c\/h4\u003e\u003cul\u003e\u003cli\u003ePreformed loop cable, 40 ft lead-in cable and splice enclosure as one factory-sealed assembly\u003c\/li\u003e\u003c\/ul\u003e\n\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eModel format is PLH-perimeter-lead-R: PLH-16-40-R is a 16 ft perimeter loop with a 40 ft lead-in.\u003c\/li\u003e\n\u003cli\u003eInstall in a shallow trench that holds the loop and lead-in, secure the corners with corner brackets, then backfill with at least 6 in of cover over the loop.\u003c\/li\u003e\n\u003cli\u003eFor new asphalt or poured concrete, use the standard PLH version.\u003c\/li\u003e\n\u003cli\u003eNot for saw cutting into existing pavement. Use a Reno A\u0026amp;E PLA or PLB loop for saw-cut retrofits.\u003c\/li\u003e\n\u003cli\u003eRequires a vehicle loop detector, sold separately.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Reno A\u0026E","offers":[{"title":"Default Title","offer_id":21952868227,"sku":"PLH-16-40-R","price":306.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/PLH-R_f9c65d75-b3e0-49d4-8c3b-7cd5f42ad20d.png?v=1772661523"},{"product_id":"reno-a-e-plh-90-perimeter-preformed-loop","title":"Reno A\u0026E PLH-90-50 EverLoop Heavy-Duty Preformed Loop - 6'x39' w\/ 50' Lead","description":"\u003cp\u003eThe Reno A\u0026amp;E PLH-90-50 is a prefabricated inductive loop and lead-in assembly for new hot-asphalt overlay or poured concrete. It is sized for a 6 ft x 39 ft rectangular loop (90 ft perimeter) with a 50 ft lead-in cable. The loop cable, lead-in and splice enclosure arrive joined and tested, so there are no field splices at the loop.\u003c\/p\u003e\n\u003cp\u003eLoop and lead-in cables are a low-profile 0.360 in OD to resist reflective cracking in asphalt. Wire insulation and cable jackets are cross-linked polyethylene (XLPE), and the cables are filled with water block gel. The splice enclosure is high-impact, glass-impregnated plastic with soldered, sealed and tested connections. Reno A\u0026amp;E puts typical detection height at about 2\/3 of the shortest loop side, roughly 4 ft on this 6 ft wide loop. Covered by a 10-year limited warranty.\u003c\/p\u003e\n\u003ch4\u003eWhat's Included\u003c\/h4\u003e\u003cul\u003e\u003cli\u003ePreformed loop cable, 50 ft lead-in cable and splice enclosure as one factory-sealed assembly\u003c\/li\u003e\u003c\/ul\u003e\n\u003ch4\u003eBefore You Order\u003c\/h4\u003e\u003cul\u003e\n\u003cli\u003eModel format is PLH-perimeter-lead: PLH-90-50 is a 90 ft perimeter loop with a 50 ft lead-in.\u003c\/li\u003e\n\u003cli\u003eAsphalt: set the loop on the base lift, hold it with mastic tape or corner brackets, and cover the loop and splice with at least 1 in of asphalt before heavy equipment drives on it.\u003c\/li\u003e\n\u003cli\u003eConcrete: hold the loop at least 2 in above the rebar on 1\/2 in poly support tees and 3\/8 in rebar, with no more than 2 ft of cable unsupported. Support tees are sold separately.\u003c\/li\u003e\n\u003cli\u003eNot for saw cutting into existing pavement. Use a Reno A\u0026amp;E PLA or PLB loop for saw-cut retrofits.\u003c\/li\u003e\n\u003cli\u003eFor dirt or gravel with no pavement, use the PLH-R direct-burial version.\u003c\/li\u003e\n\u003cli\u003eRequires a vehicle loop detector, sold separately.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Reno A\u0026E","offers":[{"title":"Default Title","offer_id":21952869443,"sku":"PLH-90-50","price":367.5,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1320\/8633\/files\/PLH_db0ab532-dd0b-4e57-8fcb-60041ec0e519.png?v=1775491995"}],"url":"https:\/\/www.proteccontrols.com\/collections\/vehicle-detection.oembed?page=9","provider":"Protec Controls","version":"1.0","type":"link"}