BASE LD-1800 Plug in loop detector ***Discontinued - Replaced by EDI LMA-1800***
BASE LD-1800 Plug in loop detector ***Discontinued - Replaced by EDI LMA-1800***
- Current Trade Policy Costs Included In Price
- In Cart Discounts Offered on Many Products
- GSA, Net 30 and purchase orders available
Description
Discontinued by BASE. The EDI LMA-1800 is the updated version. The BASE LD-1800 was a single-channel plug-in loop detector with two programmable solid-state outputs, mounted on a printed circuit board. Its DEFLECTOMETER display showed the loop reading to help set sensitivity and frequency so the detector picks up all vehicles, including motorcycles.
The EDI LMA-1800 runs on 12 VDC, 24 VDC or 24 VAC and uses a rear 10-pin Molex connector. It has 10 sensitivity levels, 4 loop frequencies and a 20 to 2500 µH inductance range. Output A is presence (fail-safe or fail-secure). Output B can be set for fault, pulse on entry, pulse on exit or a copy of output A. Loop fault memory keeps the last faults through a power loss.
Before You Order
- Orders for the LD-1800 are filled with the EDI LMA-1800.
- The LMA-1800 is plug-compatible with many gate operators, including Linear APeX, FAAC/Advanced Access Automation, All-O-Matic, Chamberlain/Elite, Viking and Apollo.
- Confirm your operator takes a 10-pin plug-in detector before ordering.
- DEFLECTOMETER®: The front panel 7-segment LED DEFLECTOMETER®
provides visual feedback and assistance for setting the correct sensitivity,
reading the frequency of the loop, reporting Loop Faults, and indicating Delay
& Extension Timing functions. - Sensitivity Meter: With a typical size vehicle over the
roadway loop, the DEFLECTOMETER® functions as a Sensitivity Meter. The optimum
sensitivity setting should provide a reading of “5”. You can adjust the
DEFLECTOMETER® reading by using the front panel UP or DOWN sensitivity buttons.
Automatic quantitative feedback of the loop system operation ensures that the
detector is set to the most optimum sensitivity level to detect ALL vehicles,
including motorcycles and high-bed vehicles. - Frequency Meter: Following power-up or reset, the
DEFLECTOMETER® will indicate a 2 or 3 digit number (quickly flashes) that
indicates the loop frequency of the loop & loop network. Keeping your loops
separated by at least 5 KHz avoids crosstalk problems and future service calls.
- Ten (10) Levels of Sensitivity: 10 levels of sensitivity (0
to 9) can be easily set using the UP or DOWN push buttons. - One Model Covers ALL Low Voltages: LMA-1800 operates on
12VDC, 24VDC, and 24VAC - Advanced Loop Diagnostics: The Loop Fault Monitor
continually checks the integrity of the loops and will report and store 3 types
of loop faults; Open Loops, Shorted Loops, and 25% sudden changes in
inductance. - Loop Fault Memory: The Loop Fault Memory uses internal
Non-Volatile memory to store and display the current and previous loop faults
utilizing the front panel “Loop Fault” LED and DEFLECTOMETER®. A power loss or
reset will not delete this memory. A MUST FOR TROUBLESHOOTING! - Call Output Memory: The detector will not drop a Call state
if power is lost for a minimum of 4 seconds or less. - Two Second Delayed Detection: A 2-second CALL delay time can
be provided via the program DIP switch. - Automatic Tuning
- Lightning & Surge Protection
- Four (4) Frequency Levels
- Compatible with ALL radio controls & remote openers
- Sensitivity Boost
- Fail Safe and Fail Secure Configurations
- Separate Color-Coded LED indicators
- Wide Loop Inductance Range: 20 to 2500 micro Henries
- Product Type: Single-channel plug-in loop detector (discontinued)
- Model: BASE LD-1800, replaced by EDI LMA-1800
- Detection: Inductive loop, DEFLECTOMETER display, 2 solid-state outputs
- Mounting: Printed circuit board plug-in
Plug Compatible with the following Operators:
- All Linear Operators with APeX controller
- Advanced Access Automation/FAAC CSL2000, CSW2000, RSW1000
- All-O-Matic SL100-DC
- Chamberlain/Elite SL3000, CSW200
- Intelligate Systems IQ500, IQ5000
- SECOM Late model operators with 10-pin Molex connectors
- Rotary Gate Systems SL1000R, SL1000C, SL1000I
- TyMetal TYM 1000 , TYM 2000
- Viking Access Models L-3, F-1, T-21, H-10, B-12, Q-4
* All Linear Operators with APeX controller
* Advanced Access Automation/FAAC CSL2000, CSW2000, RSW1000
* All-O-Matic SL100-DC
* Chamberlain/Elite SL3000, CSW200
* Intelligate Systems IQ500, IQ5000
* SECOM Late model operators with 10-pin Molex connectors
* Rotary Gate Systems SL1000R, SL1000C, SL1000I
* TyMetal TYM 1000 , TYM 2000
* Viking Access Models L-3, F-1, T-21, H-10, B-12
Detects vehicles over a buried loop to open, hold or reset a gate or barrier.
- Residential driveway gates
- Commercial slide and swing gates
- Barrier arm lanes
- Ticket dispensers and card readers
- Free exit and safety loops
All in stock orders typically ship the same business days or within 1-2 business days. Cut off for same day shipping is 2:30PM Central Time.
LEADTIME
Items with lead times typically ship in 4-7 business days.
FREE SHIPPING POLICY
Orders with free shipping may have longer lead times due to those items being shipped the most economical way. Free shipping on most orders over $195.00 does not include gate operators, loop sealant, and any extreme length or weight items
Our return policy lasts for only 30 days. If 30 days have gone by since your purchase, unfortunately we can’t offer you a refund. Some items such as Gate Operators or custom parts may not be returnable or carry a restocking fee if returned.
Protec Controls accepts purchase orders please contact us.
NET 30
We also support Net 30 terms on our website for easy ordering. Please fill out the form to the right with your company information and we will get your account setup to place Net 30 orders.
GOVERNMENT & GSA
Protec Controls accepts GSA SmartPay cards along with all major credit cards. For government quotes and purchase orders please email govsales@proteccontrols.com
