DoorKing 1602 Manuals & Support

The DoorKing 1602 is the 1 HP, 115 VAC version of the 1601 barrier gate operator. The 1602-090 and 091 run arms up to 28 ft in about 5.5 seconds.

The 1602-590 runs a 14 ft arm in about 3.5 seconds. It shares the 1601 manual and the 1601-010 control board.

Identify your model

Use the 1601/1602 manual for circuit board 1601-010 Rev AK or higher. The 1602-091 has Convenience Open.

For 14 ft arms at 2.5 seconds see the 1601.

Key specs

Class UL 325 Class II, III and IV
Motor 1 HP, 115 VAC, 9.7 A
1602-090/091 Arms up to 28 ft, about 5.5 seconds
1602-590 Arms up to 14 ft, about 3.5 seconds
Board 1601-010 Rev AK or higher

Manuals and documents

Installation Manual

Parts List

Troubleshooting

Find which part has the problem first: the operator, the loop system or the keying devices. The input LEDs show which inputs are active.

Operator will not run, power LED off

  • Check that power to the operator is on.
  • Check for 115 VAC at board terminals 1 and 2. If it reads 0, check the supply. If it is good, replace the board.

Operator will not run, power LED on

  • On a 1/2 HP 1601, press the reset button on the bottom of the motor. The 1 HP motor has no reset button.
  • Jumper terminals 6 and 14 for a moment. If the input LED does not light, check the terminal strip or replace the board.
  • Test the motor as the manual shows. If it does not run both ways, check the motor, capacitor and wiring.

Arm goes up but will not come down

  • Check the LEDs on terminals 6, 7 and 9. Any that stay on hold the arm up.
  • Check the loop detector LEDs. Any that stay on hold the arm up.
  • If the auto timer is off, check that SW 1, switch 6 is ON. For the down loop, check that SW 1, switch 4 is ON.

Loop detector LED stays on

  • Press the reset button on the detector, or lower its sensitivity.
  • Check the loop wire to ground with a megohm meter. It should read 100 megohms or more. Under 50 megohms, replace the loop.
  • The lead-in must be twisted at least 6 turns per foot and all splices soldered.

Arm does not rise on power loss

  • Check that the backup toggle switch is ON and the batteries are charged.
  • Check the 1473-010 backup board settings in the manual.

Common questions

The 1602-090 and 091 run arms up to 28 ft. The 1602-590 runs a 14 ft arm faster.

No. The reset button is on the 1/2 HP 1601 motor only.

Yes. The 1602-303 kit adds 3 ft to the octagon arm, with a reverse edge.

Replacement parts

Placa de circuito de repuesto Doorking 1601-010
Placa de circuito de repuesto Doorking 1601-010
Doorking
Login to view price.

Safety devices and accessories

DoorKing 1601-154 heater and fan kit
Calentador con ventilador Doorking 1601-154
Doorking
Login to view price.
DoorKing 2600-266 operator high voltage kit
Kit de alto voltaje para operador Doorking 2600-266
Doorking
Login to view price.
DoorKing 8080-057 retro-reflective photo eye
Doorking 8080-057 Retro-Reflective Photoeye
Doorking
Login to view price.
DoorKing 9411-010 single channel loop detector with aux relay
DoorKing 9411-010 single channel loop detector with aux relay - view 2
Detector de bucle de un solo canal Doorking 9411-010 con relé
Doorking
Login to view price.