Operador de puerta corrediza lineal OSCO VS-GSLG-121 de 1 HP con velocidad variable

• Controlador APeX integral
• Velocidad de compuerta de hasta 24"/seg.
• Arranque suave/parada suave
• Control de velocidad programable
• Accionamiento directo de cara C con freno
• Cadena de transmisión de rodillos n.° 50
• Manija de desconexión manual de emergencia
• Acabado con pintura en polvo
• Montaje en poste estándar; montaje en almohadilla opcional

Eléctrico

• Velocidad variable: arranque y parada suaves programables mediante variador de frecuencia.
• Motores industriales trifásicos de servicio continuo de 1/2 a 2 HP con bastidor 56
• Freno de doble cara C
• Interruptor de encendido/apagado
• Receptáculo dúplex en unidades de 115 VCA
• Estación de control de tres botones del controlador APeX integrado
• Alimentación CA y CC disponible para accesorios de control de acceso y dispositivos de inversión
• Todas las conexiones de accesorios 24 VCC
• Interruptores de límite rotativos fácilmente ajustables

Mecánico

• Reductor de engranajes de cara C en ángulo recto 10:1 para trabajo pesado
• Cadena de rodillos y piñones n.° 50
• Limitador de par ajustable
• Cojinetes de bloque de almohada de alta resistencia

• Max Gate Length: 78 ft
• Max Gate Weight: 2,500 lb
• Motor: 1 HP, three-phase 56-frame, variable frequency drive
• Input Power: 208/230 VAC single-phase
• Operating Voltage/Accessory Power: 24 VDC accessory power
• Duty Cycle: Continuous
• UL 325 Class: ETL listed, UL 325 compliant (class not stated)
• Battery Backup: Not available
• Solar Capable: No
• Drive: Direct C-face drive, 10:1 gear reducer, #50 roller chain, double C-face brake
• Gate Speed / Open Time: Up to 24 in per second, programmable
• Mounting: Post mount standard; pad mount optional
• Warranty: 5 years

Power Wiring

• Electrical Connections: All AC electrical connections to the power source and the operator must be made by a licensed electrician and observe all national and local electrical codes; use copper wire only
• Wire Run: Distance is measured in ft from the operator to the power source; do not exceed the maximum distance for the model, voltage, horsepower and wire gauge
• Basis: Based on standard 115 V and 230 V supplies with a 10% drop allowable, per National Electrical Code Article 430 (motor inrush, brake solenoids and operator requirements)
• Junction Box: A separate junction box (not supplied) may be needed when large-gauge wire is used
• Ground: The green ground wire must be properly connected

Mounting Pad Installation

• Mounting: Bolted to two 3 - 3-1/2 in OD galvanized posts secured in concrete footings (length per local codes, frost line depth and soil conditions); optional pad mounting per Linear drawing #2700-360
• Side Plates: Four 3/16 in side plates on the outside top and bottom, two 1/2 in side plates on the inside top, two 3/16 in side plates on the inside bottom; attached with the U-bolts and hardware provided
• Gate Preparation: Gate must roll or slide freely with exposed rollers covered; gate covered with fabric with openings no larger than 2-1/4 in to a minimum height of 72 in above ground (mesh optional on picket gates with pickets less than 2-1/4 in apart)
• Pedestrians: Operator is for vehicular gates only; a separate pedestrian access opening must be supplied

Hoja de especificaciones

Manual de instalación

Especificaciones de cables eléctricos

Instrucciones de montaje del VS-GSLG

Disposición del bucle de la puerta corrediza