Part of the EZ Parts Finder: pick a part on the diagram or use the list below.
Here is a parts diagram for the HySecurity SlideDriver II SD15 slide gate operator, the model that replaced the 222 SS ST. The photo views show the main chassis, the drive layer, the pump pack, both sides of the control box and the back. The list below names each SD15 part with its MX part number, sorted by assembly, from the pump pack to the SmartTouch 725 controller.
Identify your model
A SlideDriver II has a SmartTouch 720 or 725 controller, which sets it apart from the original SlideDriver. The SD15 and SD40 use a 1 HP motor, the SD50F and SD80V use 2 HP, and the SD200V uses 5 HP. Check the voltage and phase marked on the operator before ordering, because each unit is built for one line voltage and phase.
Related models: HySecurity SlideDriver 15, HySecurity SlideDriver 30F, HySecurity SlideDriver 40, HySecurity SlideDriver 50VF2/3
Operator and manuals
- Operator: HySecurity SlideDriver II SD15 (Replaces 222 SS ST) Slide Gate Operator
- Installation manual (MX5386) (PDF)
- Programming and operations manual (MX5386-01) (PDF)
- User guide (MX5385-01) (PDF)
- Quick start guide (PDF)
- SD15 spec sheet (PDF)
Most ordered parts
- HySecurity MX002707 SlideDriver 6" Drive Wheel (MX002707)
- HySecurity MX001827/MX4994 Wheel, AdvanceDrive, Replacement, 6 inch (MX001827)
- HySecurity MX4752 SlideDriver Hydraulic Motor RS-10" Standard (MX4752)
- HySecurity MX001103 Release, Manual, Toggle Assembly (MX001103)
- Hysecurity MX5493 Limit Sensor for SlideDriver II (MX5493)
- HySecurity MX5626 SmartTouch 725 Controller (MX5626)
- HySecurity MX5306 I/O Expansion Module (MX5306)
- HySecurity MX5502 Pressure Transducer, 3000 PSI (MX5502)
Parts list by assembly
Main
Drive Layer
Pump Pack
| Part number | Part |
|---|---|
| MX002054 | HySecurity MX002054 Coupler, Motor, 5/8 inch Shaft, 6T, New |
| MX000174 | HySecurity MX000174 3000 PSI Relief Valve |
| MX5502 | HySecurity MX5502 Pressure Transducer, 3000 PSI |
| MX000686 | HySecurity MX000686 SlideDriver Breather Cap |
| MX5245 | HySecurity MX5245 Directional Valve Kit |
| MX000161 | HySecurity MX000161 Reservoir, 4 Qt |
Control Box
| Part number | Part |
|---|---|
| MX5626 | HySecurity MX5626 SmartTouch 725 Controller |
| MX4097 | Hysecurity MX4097 3Phase Power Supply, 120W, 24VDC |
| MX5106 | HySecurity MX5106 1Phase Power Supply, 24VDC, 120W |
| MX4105 | Hysecurity MX4105 Contactor, AC Motor |
| MX5306 | HySecurity MX5306 I/O Expansion Module |
Common questions
What power options does the SlideDriver II SD15 come in?
The SD15 has a 1 HP motor. It runs on single phase 115, 208 or 230 V, or three phase 208, 230 or 460 V.
How do I release the SlideDriver II to move the gate by hand?
With the gate stopped, remove the cover, set the power switch to OFF, then unclamp the toggle handle and secure it open. The mechanism is spring loaded and drops fast. Clamp the handle, turn power on and press STOP or RESET to return to automatic operation.
What breaker does the SD15 need?
HySecurity specifies a dedicated 20A circuit with a 20A inverse time breaker. Only the 50F and 80V single phase units and the 200V three phase units need a 30A breaker.