HySecurity StrongArm Manuals & Support

The HySecurity StrongArm is a hydraulic barrier arm operator for traffic lanes, with arms from 10 ft to 36 ft. It is rated for 2,000 cycles per day and runs on the Smart Touch Controller.

Models are the StrongArm 14F, 20, 28, 36 and the StrongArmDOT 28. Optional UPS systems keep the lane cycling after a power loss.

Identify your model

The part number is on the operator label and starts with HTG 320.

Part number	Model	Max arm	Open / close
HTG 320-2 ST	StrongArm 14F	14 ft	2 s / 3 s
HTG 320-3 ST	StrongArm 20	20 ft	3 s / 4 s
HTG 320-6 ST	StrongArm 28	28 ft	5 s / 6 s
HTG 320-8 ST	StrongArm 36	36 ft	8 s / 8 s
HTG 320-6 DOT ST	StrongArmDOT 28	28 ft	5 s / 6 s

The StrongArmPark DC is a different electromechanical operator. See the StrongArmPark DC support page.

Key specs

Models	StrongArm 14F, 20, 28, 36, StrongArmDOT 28
Drive	Hydraulic, 3/4 hp
Duty cycle	2,000 cycles per day
Arm length	Up to 14, 20, 28 or 36 ft by model
Open time	2 to 8 seconds by model
Power	115/208/230 VAC 1-phase or 208/230/460 VAC 3-phase
Controller	Smart Touch with 70+ settings; S.T.A.R.T. software on a PC
Relays	Three user relays; Hy8Relay adds eight more
UL 325 usage class	Class I, II, III and IV
Operating temperature	-40 to 158 °F

Manuals and documents

Installation Manual

StrongArm Breakaway Arm Installation
2015 · 4 pages View PDF: StrongArm Breakaway Arm Installation (opens in a new tab)
StrongArm 36 Arm Rigging (HTG 320-8)
5 pages View PDF: StrongArm 36 Arm Rigging (HTG 320-8) (opens in a new tab)
StrongArm Flashing Light Kit (MX3426)
2 pages View PDF: StrongArm Flashing Light Kit (MX3426) (opens in a new tab)
StrongArm Heater Installation
D0036 · 1 page View PDF: StrongArm Heater Installation (opens in a new tab)
StrongArm Pump Pack Replacement
D0235 · 6 pages View PDF: StrongArm Pump Pack Replacement (opens in a new tab)
HyNet Attachment Kit Installation
D0717 · 8 pages View PDF: HyNet Attachment Kit Installation (opens in a new tab)

Programming Guide

StrongArm Programming and Operations Manual
MX3657-01 Rev. D, 2020 · 134 pages View PDF: StrongArm Programming and Operations Manual (opens in a new tab)
S.T.A.R.T. Software User Guide
D0049 Rev. F, 2013 · 23 pages View PDF: S.T.A.R.T. Software User Guide (opens in a new tab)

Troubleshooting

The Smart Touch Controller shows codes on the display and the buzzer chirps. An Alert clears with a new command. A Fault clears with the Stop or Reset button. An Error clears only with the Reset button or by cycling power.

Open and Close do nothing

Check that line voltage matches the nameplate, within 10%.
Check 24 VDC at the power supply and reset the breaker on the transformer if it tripped.
With no external Stop button, a jumper must connect COM to STOP.

Pump runs but the arm does not move

Check the hydraulic fluid level.
On 3-phase power, check motor rotation. Swap any two AC lines to reverse it.
Check the pressure gauge and the pressure relief valve.

Arm only opens or only closes

Only opens: the directional valve may be stuck with debris.
Only closes: the directional valve coil is not getting power or has failed.

Breakaway arm

If the arm was knocked off, reset the breakaway bracket and check the kill switch wiring before you run the operator.

Common questions

An alert clears with a new Open or Close command. A fault clears with the Stop or Reset button. An error clears only with the Reset button or by cycling power.

Read the HTG 320 part number on the label. HTG 320-2 is the 14F, 320-3 is the 20, 320-6 is the 28, 320-8 is the 36 and 320-6 DOT is the StrongArmDOT 28.

Yes, with the optional DC Power Supply with HyCharger DC or the AC Power Supply with HyInverter AC. HySecurity lists up to 300 cycles after an AC power loss.

If the arm only opens, the directional valve is likely stuck with debris. If it only closes, check power to the directional valve coil and the coil itself.

Replacement parts

Parts diagram: HySecurity StrongArm Parts Diagram and Replacement Parts